Range Rover Evoque: Differential Rear Bushing
Special Tool(s)
205-860-09
Installer, Differential Bushing
205-861-01
Remover, Differential Bushing
205-861-02
Remover/Installer, Differential Bushing
205-861-03
Installer, Differential Bushing
205-861-04
Installer, Differential Bushing
205-861-05
Installer, Differential Bushing
LR-121
Hydraulic Cylinder 10t
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Remove both rear wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
3. Remove the rear differential.
Refer to: Differential Case - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
4. Take note of the fitted position of the rear bushings.
The RH bushing slot is positioned vertically and the LH bushing slot is positioned horizontally.
5. CAUTION: Note the fitted position of the component prior to removal. Using the special tool, remove the bushing.
Special Tool(s): 205-861-01, 205-861-02, LR-121
Installation
1. CAUTION: Only use the specified special tool. Using the special tool, compress the bushing.
Special Tool(s): 205-860-09, 205-861-05, LR-121
2. CAUTION: Make sure the correct special tool is used to install the bushings to the correct depth.
NOTE: Make sure that these components are installed to the noted removal position. Using the special tool, install the bushing, making sure the slot on the RH bushing is positioned vertically and the slot on the LH bushing is positioned horizontally.
Special Tool(s): LR-121, 205-861-04, 205-861-03, 205-861-05
3. Install the rear differential.
Refer to: Differential Case - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
4. Install the rear wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
READ NEXT:
Drive Pinion Flange Vehicles With: AWF21
6-Speed Automatic Transmission
Special Tool(s)
205-053
Retainer, Drive Flange
Removal
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
Vehicles with diesel engine
2. Refer t
Drive Pinion Front Bearing
Special Tool(s)
100-012
Slide Hammer
205-067
Preload Gauge
308-615
Remover, Seals
JLR-205-972
Mounting Bracket, Rear Axle
JLR-205-984
Remover/Installer, Drive Pinion Nut
JLR-205-985
Remover, Drive Pin
Active On-Demand Coupling Vehicles With:
M66 6-Speed Manual Transmission AWD
Removal
1. WARNING: Make sure to support the vehicle with axle stands.
Raise the vehicle on a lift.
2. Remove the exhaust system.
Refer to: Exhaust System (309-00B Exhaust System - TD4 2.2L
Diesel, R
SEE MORE:
Wiring Harness - Description and Operation
Introduction
CAUTION: Do not use any other heat shrink sleeve other than the approved
glue lined heat shrink sleeve mentioned
in the repair procedure.
The purpose of this document is to promote quick and efficient minor repair
to harness connectors or cables using
approved methods and the wiring
Engine Wiring Harness TD4 2.2L Diesel, Vehicles With:
AWF21 6-Speed Automatic Transmission
Removal
CAUTIONS:
Make sure that the wiring harness is not twisted or damaged on removal. Failure
to follow this instruction may result
in damage to the vehicle.
Take extra care not to damage the wiring harness clips.
NOTES:
Some variation in the illustrations may occur, but the essential informa
