Range Rover Evoque: Headlamp Assembly
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2.
3.
4. NOTE: Some components shown removed for clarity.
5.
6.
7.
8.
9. Remove all bumper lower fixing to assist the partial removal of the bumper.
10. Torque: 4 Nm
11. Carefully move the bumper to gain access to the headlamp assembly.
12.
Installation
1. To install, reverse the removal procedure.
2. Check the headlamp alignment and adjust if necessary.
Refer to: Headlamp Adjustment (417-01 Exterior Lighting, General Procedures).
Rear Lamp Assembly
Removal
1.
2. Torque: 1 Nm
3. NOTE: Do not disassemble further if the component is removed for access only.
Installation
1. To install, reverse the removal procedure.
High Mounted Stoplamp
Removal
NOTE: Removal steps in this procedure may contain installation details.
1.
2.
3. Torque: 1.5 Nm
Installation
1. To install, reverse the removal procedure.
Headlamp Leveling Module
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct.
1. Refer to: Glove Compartment (501-12 Instrument Panel and Console, Removal and Installation).
2. NOTE: LHD illustration shown, RHD is similar. Torque: 7 Nm
Installation
1. To install, reverse the removal procedure.
2. Using the diagnostic tool, configure the new unit using the Programmable Module Installation Routine.
Stoplamp Switch
Removal
NOTES:
Removal steps in this procedure may contain installation details.
LHD illustration shown, RHD is similar.
1.
2.
Installation
1. To install, reverse the removal procedure.
Front Fog Lamp RH
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Front Bumper Cover (501-19 Bumpers, Removal and Installation).
3. Torque: 2 Nm
Installation
1. To install, reverse the removal procedure.
2. Check the fog lamp beam alignment.
Refer to: Front Fog Lamp Adjustment (417-01 Exterior Lighting, General Procedures).
READ NEXT:
Headlamps
Principle of Operation
Three types of headlamp are available: Halogen, bi-xenon or Adaptive Front
Lighting System (AFS).
For a detailed description of the headlamps operation, refer to the relevant
Stoplamps
Principle of Operation
For information on the description and operation of the system, refer to
relevant section of the workshop manual. REFER
to: (417-01 Exterior Lighting)
Note that the stoplamps w
Interior Lighting
Interior Lighting
RH (right-hand) vanity mirror lamp
Front overhead console
RH rear door module
RH rear interior lamp
RH rear door latch mechanism
Load space lamp
LH (left-hand) rear interior
SEE MORE:
Front Wheel Bearing
Special Tool(s)
204-305
Remover, Wheel Bearing
204-726
Remover/Installer, Wheel Bearing
204-727A
Installer, Wheel Bearing
JLR-204-806
Support Tool, Wheel Knuckle
JLR-204-807
Installer, Front Wheel Bearing
JLR-204-808
Installer, Front Wheel Bearing
General Equipment
Copper Hammer
Hydraulic press
Dealer locations
Details of Land Rover Dealers are held on the
Navigation System hard drive as a points of
interest (POI) category. Certain Dealers may be
located in areas that are not fully mapped on
the hard drive. If a route is set to one of these
Dealers, guidance may only be possible to the
nearest town c
