Range Rover Evoque: Active On-Demand Coupling Module
Removal
NOTE: If a new Active on-demand coupling module is installed, the throttle valve must also be installed.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2.
3. CAUTIONS:
Make sure that the area around the component is clean and free of foreign material.
Be prepared to collect escaping fluids.
4.
Installation
1.
2. CAUTION: The throttle valve must be installed to the active on-demand coupling module before the assembly is installed to the active on-demand coupling.
Failure to follow this instruction may result in damage to the vehicle.
3. NOTE: Lubricate the O-ring seal. Torque: 6 Nm
4.
Active On-Demand Coupling Oil Pump
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise the vehicle on the lift.
2. Refer to: Drive Pinion Flange - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
3.
4. CAUTIONS:
Be prepared to collect escaping oil.
Make sure that the area around the component is clean and free of foreign material.
Lubricate the O-ring seals.
Only use the specified material to lubricate the seals.
NOTES:
Remove and discard the O-ring seals.
Install new O-ring seals.
Torque: 6 Nm
Installation
1. To install, reverse the removal procedure.
2. Check and top-up the active on-demand coupling fluid level.
Refer to: Active On-Demand Coupling Filling (205-02 Rear Drive Axle/Differential, General Procedures).
Active On-Demand Coupling Drive Pinion Seal
Special Tool(s)
100-012
Slide Hammer
205-862-1
Installer, Active On-demand Pinion Seal
308-529
Remover, Seals
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise the vehicle on the lift
2. Remove the differential drive flange.
Refer to: Drive Pinion Flange - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Drive Pinion Flange - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
3. Carefully remove and discard the pinion oil seal.
Special Tool(s): 308-529, 100-012
Installation
1. CAUTION: Only use the specified material to lubricate the seals. Lubricate the oil seal.
Refer to: Specifications (205-02 Rear Drive Axle/Differential, Specifications).
2.
- Using the special tool, install a new oil seal.
Special Tool(s): 205-862-1
- Tap in the seal until the head of the drift is against the active on-demand coupling housing.
3. Install the differential drive flange.
Refer to: Drive Pinion Flange - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Drive Pinion Flange - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
READ NEXT:
Differential Case Vehicles With: AWF21
6-Speed Automatic Transmission
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Remove th
Differential Support Insulator
Removal
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Support the rear differential using a transmission jack.
3. CAUTION: Mark the components to aid
Differential Rear Bushing
Special Tool(s)
205-860-09
Installer, Differential Bushing
205-861-01
Remover, Differential Bushing
205-861-02
Remover/Installer, Differential Bushing
205-861-03
Installer, Differential Bushing
205-86
SEE MORE:
Supervisor screen controls
Supervisor screen controls
See 104, TOUCH SCREEN OVERVIEW.
1. Select rear media.
2. Current rear media display.
3. Left screen select.
4. Right screen select.
5. Settings screen.
6. Remote control lock.
7. Turns off the selected screen.
8. Turns off the selected system.
9. Audio source s
Rear Lamp Mounting Panel
Removal
NOTES:
The rear lamp mounting panel is manufactured from mild steel.
The section of the rear lamp mounting panel described within this procedure is
for the access for installation of the
inner back panel assembly.
The upper NVH component must be replaced when a complete panel is installed
