Range Rover Evoque: Climate Control Assembly

Removal

NOTE: Removal steps in this procedure may contain installation details.

All vehicles

1. CAUTION: LH illustration shown, RH is similar.

Torque: 1.9 Nm

Vehicles with manual transmission

2. Refer to: Gearshift Lever Knob (308-06 Manual Transmission/Transaxle External Controls, Removal and Installation).

3.

All vehicles

4.

Vehicles with manual transmission

5.

Vehicles with automatic transmission

6.

All vehicles

7.

8. NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Torque: 1.1 Nm

9. NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Torque: 1.1 Nm

Installation

1. To install, reverse the removal procedure.

2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.

Driver Side Register

Removal

NOTE: Removal steps in this procedure may contain installation details.

1.

2.

3.

4.

5. Torque: 4 Nm

6. CAUTION: Care must be taken to avoid damaging the driver side register internal components.

Torque: 1.5 Nm

Installation

1. To install, reverse the removal procedure.

Pollen Filter

Removal

NOTE: Removal steps in this procedure may contain installation details.

All vehicles

1. NOTE: LHD illustration shown, RHD is similar.

2. NOTE: LHD illustration shown, RHD is similar.

Left-hand drive vehicles

3. CAUTION: Take extra care not to damage the wiring harnesses.

Torque: 10 Nm

All vehicles

4. NOTE: LHD illustration shown, RHD is similar.

5. NOTE: LHD illustration shown, RHD is similar.

Installation

1. CAUTION: Take extra care not to damage the pollen filter.

To install, reverse the removal procedure.

Passenger Side Register

Removal

NOTE: Removal steps in this procedure may contain installation details.

1.

2.

3.

4. NOTES: Left-hand shown, right-hand similar.

The step must be carried out on both sides.

5. Torque: 4 Nm

6.

7. Torque: 1.5 Nm

8. CAUTION: Care must be taken to avoid damaging the passenger side register internal components.

Torque: 1.5 Nm

Installation

1. To install, reverse the removal procedure.

Recirculation Blend Door Actuator

Removal

NOTES: LHD shown, RHD is similar.

Removal steps in this procedure may contain installation details.

1. Disconnect the battery ground cable.

Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).

2. Refer to: Central Junction Box (CJB) (418-00 Module Communications Network, Removal and Installation).

3.

4.

5. Torque: 10 Nm

6.

7.

8.

9.

10.

Installation

1. To install, reverse the removal procedure.

Plenum Chamber

Removal

NOTES: Removal steps in this procedure may contain installation details.

RHD illustration shown, LHD is similar.

1. Refer to: Wiper Pivot Arm (501-16 Wipers and Washers, Removal and Installation).

2. Repeat the above procedure for the other wiper arm.

3.

4.

5. Torque: 25 Nm

6. Torque: 25 Nm

7.

8. NOTE: Repeat the above step for the other side.

9.

10. NOTE: Do not disassemble further if the component is removed for access only.

Installation

1. To install, reverse the removal procedure.

Thermostatic Expansion Valve TD4 2.2L Diesel

Removal

NOTE: Removal steps in this procedure may contain installation details.

1. Disconnect the battery ground cable.

Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).

2. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging - TD4 2.2L Diesel (412-00 Climate Control System - General Information, General Procedures).

3. Refer to: Engine Control Module (ECM) (303-14A Electronic Engine Controls - TD4 2.2L Diesel, Removal and Installation).

4. CAUTIONS: Make sure that all openings are sealed. Use new blanking caps.

Torque: 9 Nm

5. Torque: 4 Nm

Installation

1. To install, reverse the removal procedure.

READ NEXT: