Range Rover Evoque: Transfer Case Fluid Level Check
CAUTION: The fluid filler plug is not a fluid level plug.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Make sure that the area around the component is clean and free of foreign material.
NOTE: Remove and discard the sealing washer.
4. CAUTION: The fluid filler plug is not a fluid level plug. Fill the transfer case with the recommended fluid.
Refer to: Specifications (308-07B Transfer Case - Vehicles With: AWF21 6-Speed Automatic Transmission/M66 6-Speed Manual Transmission AWD, Specifications).
5. NOTE: Install a new sealing washer. Torque: 35 Nm
6. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
Power Transfer Unit GTDi 2.0L Petrol
Removal
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Air Cleaner Intake Pipe (303-12B Intake Air Distribution and Filtering - GTDi 2.0L Petrol, Removal and Installation).
3. Refer to: Front Halfshaft RH - LHD AWD/RHD AWD (205-04 Front Drive Halfshafts, Removal and Installation).
4. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
5. Torque: 24 Nm
6. CAUTIONS: Mark the position of the driveshaft flange in relation to the drive pinion flange.
To avoid damage to the joint or gaiter, do not allow the driveshaft to hang.
Make sure that the driveshaft is supported with suitable retaining straps.
The component must be aligned with the installation markings.
Torque: 40 Nm
7. CAUTION: Take extra care not to damage the component.
NOTE: LH illustration shown, RH is similar.
8. NOTE: LH illustration shown, RH is similar.
Remove the RH front wheel arch liner.
9. CAUTIONS: Discard the bolt.
Make sure that a new bolt is installed.
Torque:
- Stage 1: 50 Nm
- Stage 2: 180
READ NEXT:
Power Transfer
Unit TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to:
Transfer Case
Connecting Sleeve Seals GTDi 2.0L Petrol
Special Tool(s)
100-012
Slide Hammer
307-594
Installer, Seal
308-005
Remover, Axle oil seal
Removal
NOTE: Some variation in the illustrations may occur, but the essential
information is always correc
Transfer Case
Connecting Sleeve Seals TD4 2.2L Diesel, Vehicles With: AWF21 6-Speed
Automatic Transmission
Special Tool(s)
100-012
Slide Hammer
307-594
Installer, Seal
308-005
Remover, Axle oil seal
Removal
NOTE: Some variation in the illustrations may occur, but the essential
information is always correc
SEE MORE:
Electrical Precautions
General
The following guidelines are intended to make sure the safety of the operator
whilst preventing damage to the electrical
and electronic components of this vehicle.
Equipment
Prior to commencing any test procedure on the vehicle, make sure that the
relevant test equipment is working correct
Connecting a device
Connecting a device
1. USB/iPod sockets.
2. 3.5 mm AUX socket.
3. Rear media USB/iPod socket.
4. Rear media AV sockets.
Connect the device into the appropriate socket.
Note: Use the cable supplied with your media
device to connect to the USB socket.
When an iPod is connected, playback will
