Range Rover Evoque: Instrument Panel GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. NOTE: The procedure must be carried out on both sides. Refer to: Cowl Side Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
4. Refer to: Steering Column (211-04 Steering Column, Removal and Installation).
5. Refer to: Windshield Wiper Motor (501-16 Wipers and Washers, Removal and Installation).
6. Refer to: Thermostatic Expansion Valve - GTDi 2.0L Petrol (412-01 Climate Control, Removal and Installation).
7. NOTE: The procedure must be carried out on both sides. Refer to: Front Door (501-03 Body Closures, Removal and Installation).
8. Refer to: Glove Compartment (501-12 Instrument Panel and Console, Removal and Installation).
9. Refer to: Front Seat (501-10 Seating, Removal and Installation).
10. Refer to: Floor Console (501-12 Instrument Panel and Console, Removal and Installation).
11. NOTE: The step must be carried out on both sides.
Torque: 6 Nm
12. NOTE: The step must be carried out on both sides.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24. CAUTION: Make sure that all openings are sealed.
Use new blanking caps.
Clamp the hoses to minimize coolant loss.
25. Torque: 40 Nm
26. Torque: 24 Nm
27. NOTES:
Right-hand shown, left-hand similar.
The step must be carried out on both sides.
Torque: 24 Nm
28. NOTES:
Right-hand shown, left-hand similar.
The step must be carried out on both sides.
Torque: 40 Nm
29. CAUTION: Protect the surrounding trim to avoid damage.
NOTE: With assistance remove the component.
Torque: 24 Nm
Installation
1. To install, reverse the removal procedure.
2. Check and top-up the coolant if required.
READ NEXT:
Instrument Panel Upper Section
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables,
Specifications).
Floor Console
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Floor Console Upper Section (501-12 Instrument Panel and
Console, Removal and Installation).
2. NOTES:
The
Overhead Console
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. CAUTION: Take extra care not to damage the
edges of the component.
2.
3. NOTE: Do not disassemble further if the
co
SEE MORE:
Search area
The navigation map database is divided into
countries, or geographically defined areas
within countries, called search areas. When
setting a route, the destination (or waypoint)
entered must be in the currently selected
search area.
Before attempting to set a destination or
waypoint, set the
Engine Wiring Harness TD4 2.2L Diesel, Vehicles With:
M66 6-Speed Manual Transmission AWD/M66 6-Speed Manual
Transmission FWD
Removal
CAUTIONS:
Make sure that the wiring harness is not twisted or damaged on removal. Failure
to follow this instruction may result
in damage to the vehicle.
Take extra care not to damage the wiring harness clips.
NOTES:
Some variation in the illustrations may occur, but the essential informa
