Range Rover Evoque: Timing Cover
Special Tool(s)
303-021
Engine support bracket
JLR-303-1591
Lifting Bracket, Engine - Rear
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is always correct.
1. Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
4. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
5.
6.
7.
8.
9.
10.
11. Torque: 45 Nm
12. CAUTION: Protect the paintwork during this operation.
13.
14. NOTE: Loosen the bolt, but do not fully remove.
15.
16.
17.
18. NOTE: Make sure that all traces of the old sealant are removed from the mating faces.
Installation
1. CAUTION: Apply sealant WSE-M4G323-A6 in a 4-7mm diameter on the engine front cover as shown.
The component must be installed and tightened within 10 minutes of sealant application.
2. CAUTION: Tighten the bolts in the sequence shown.
Torque:
- M6 10 Nm
- M10 48 Nm
3. Torque: 80 Nm
4. Torque: 80 Nm
5. Torque: 110 Nm
6. NOTE: Loosen the bolt, but do not fully remove. Torque: 110 Nm
7. CAUTION: Protect the paintwork during this operation. Remove the special tool.
Special Tool(s): 303-021
8. Remove the special tool.
Special Tool(s): JLR-303-1591
9. Torque: 6 Nm
10.
11. Torque: 24 Nm
12. Torque: 20 Nm
13. Torque: 25 Nm
14.
15. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
16. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
17. Refer to: Battery (414-01 Battery, Mounting and Cables, Removal and Installation).
READ NEXT:
Valve Cover
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is
always correct.
Removal steps in this proc
Engine - Removal and Installation
Removal
Special Tool(s)
205-857
Remover, Halfshaft
1. Refer to: Battery Tray (414-01 Battery, Mounting and Cables,
Removal and Installation).
2. Refer to: Air Conditioning (A/C) System Recovery, Evacu
Engine Upper/Lower Support Insulator
Engine Upper Support Insulator
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is
always
SEE MORE:
Radio controls
Radio controls
See 104, TOUCH SCREEN OVERVIEW.
1. Radio: Waveband selection. Touch to view
and select a waveband. The radio will tune
to the last used station on that waveband.
Touch again to close.
The waveband selection box will close
automatically after 5 seconds without use.
2. Display
Ethanol
This vehicle is not suitable
for use with
fuels containing more than 10%
ethanol.
Do not use E85 fuels (85% ethanol
content). Equipment necessary for the
use of fuels containing more than 10%
ethanol is not fitted to this vehicle. If
E85 fuels are used, serious engine and
fuel system dama
