Range Rover Evoque: Differential Support Insulator
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Support the rear differential using a transmission jack.
3. CAUTION: Mark the components to aid installation.
- Discard the bolts.
4.
Installation
1. Torque: 35 Nm
2. CAUTIONS:
Make sure that new bolts are installed.
Make sure that the installation marks are aligned.
Torque: 175 Nm
Differential Front Bushing
Special Tool(s)
205-860-01
Remover, Differential Bushing
205-860-02
Remover, Differential Bushing
205-860-03
Installer, Differential Bushing
205-860-04
Installer, Differential Bushing
205-860-09
Installer, Differential Bushing
205-860-10
Spacer, Differential Bushing
LR-121
Hydraulic Cylinder 10t
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Remove both rear wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
3. Remove the rear differential.
Refer to: Differential Case - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
4. CAUTIONS:
Mark the components to aid installation.
Note the fitted position of the component prior to removal.
Using the special tools, remove the bushing.
Special Tool(s): 205-860-01, 205-860-02, 205-860-10, LR-121
Installation
1. Using the special tool, compress the bushing.
Special Tool(s): 205-860-09, 205-860-04, LR-121
2. CAUTION: Make sure the correct special tool is used to install the bushings to the correct depth.
NOTE: Make sure that these components are installed to the noted removal position.
Using the special tool, install the bushing.
Special Tool(s): 205-860-10, 205-860-01, 205-860-04, 205-860-03, LR-121
3. Install the rear differential.
Refer to: Differential Case - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
4. Install the rear wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
READ NEXT:
Differential Rear Bushing
Special Tool(s)
205-860-09
Installer, Differential Bushing
205-861-01
Remover, Differential Bushing
205-861-02
Remover/Installer, Differential Bushing
205-861-03
Installer, Differential Bushing
205-86
Drive Pinion Flange Vehicles With: AWF21
6-Speed Automatic Transmission
Special Tool(s)
205-053
Retainer, Drive Flange
Removal
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
Vehicles with diesel engine
2. Refer t
Drive Pinion Front Bearing
Special Tool(s)
100-012
Slide Hammer
205-067
Preload Gauge
308-615
Remover, Seals
JLR-205-972
Mounting Bracket, Rear Axle
JLR-205-984
Remover/Installer, Drive Pinion Nut
JLR-205-985
Remover, Drive Pin
SEE MORE:
Fender Apron Upper Panel
Removal
NOTES:
The fender apron upper panel is manufactured from mild steel.
The service panel is serviced not fully spot welded.
There is an NVH component on this panel, it is serviced on the new panel.
1. The fender apron upper panel is replaced in conjunction with:
Front bumper cover
Hood
H
Balance Shaft Assembly
Special Tool(s)
JLR-303-1595
Alignment Tool, Crankshaft Damper
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is
always correct.
Removal steps in this procedure may contain installation detail
