Range Rover Evoque: Bumpers
Front Bumper Cover
Removal
NOTE: Removal steps in this procedure may contain installation details.
1.
2.
3. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
4. NOTE: The step must be carried out on both sides. Refer to: Fender Splash Shield (501-02 Front End Body Panels, Removal and Installation).
5.
6.
7.
8. Torque: 4.5 Nm
9. NOTES:
The step must be carried out on both sides.
Do not disassemble further if the component is removed for access only.
Torque: 2 Nm
10.
11.
12.
13.
14.
15.
16.
17.
18. NOTE: The step must be carried out on both sides.
19.
Installation
1. To install, reverse the removal procedure.
Front Bumper
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Front Bumper Cover (501-19 Bumpers, Removal and Installation).
3. NOTE: The step must be carried out on both sides.
Torque: 4.5 Nm
4. NOTE: The step must be carried out on both sides. Torque: 4.5 Nm
5. Torque: 4.5 Nm
6. Torque: 4.5 Nm
7. Torque: 48 Nm
Installation
1. To install, reverse the removal procedure.
Rear Bumper Cover
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. NOTE: The procedure must be carried out on both sides. Refer to: Rear Lamp Assembly (417-01 Exterior Lighting, Removal and Installation).
2.
3. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
4. Remove the rear wheels and tyres.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
5. CAUTION: Take extra care not to damage the component.
NOTE: The step must be carried out on both sides.
6.
7.
8. Torque: 4.5 Nm
9.
10. CAUTION: Take extra care not to damage the edges of the component.
11. NOTE: Do not disassemble further if the component is removed for access only. Torque: 4.5 Nm
12. NOTE: The procedure must be carried out on both sides. Torque: 4.5 Nm
13.
14.
15.
Installation
1. To install, reverse the removal procedure.
Rear Bumper
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Rear Bumper Cover (501-19 Bumpers, Removal and Installation).
3. Torque: 30 Nm
Installation
1. To install, reverse the removal procedure.
Bumpers
Torque Specifications
READ NEXT:
Safety Belt System
Safety Belt System
Diagnosis and Testing
Principle of Operation
For a detailed description of the seatbelt system and operation, refer to the
relevant description and operation section of
the worksho
Air Bag Supplemental Restraint System
(SRS)
Component Location
COMPONENT LOCATION SHEET 1 OF 2
Battery
ECM (engine control module)
CJB (central junction box)
Passenger air bag
Overhead console
RCM (restraints control module)
Driver air
SEE MORE:
Removing the temporary spare wheel
Remove the spare wheel prior
to
jacking the vehicle, to avoid
destabilising the vehicle when raised.
Do not use power tools to
loosen the
spare wheel. Doing so may damage the
mechanism.
1. To access the temporary spare wheel, fold
forward the rear edge of the cover then
remove it.
2.
Heater Mats
Principles of Operation
Heated seats incorporate heater elements in the cushion and the backrest of
the seat. Each cushion heater element has a
thermal sensor, which supplies a feedback temperature signal to the related seat
heater module. The backrest heater
elements do not have a thermal sensor,
