Range Rover Evoque manuals

Range Rover Evoque: Engine Mount LH/RH

Land Rover Range Rover Evoque L538 (2011–2018) Service Manual / Engine / Engine - GTDi 2.0L Petrol / Engine Mount LH/RH

Engine Mount LH

Removal

NOTES:

Removal steps in this procedure may contain installation details.

Some variation in the illustrations may occur, but the essential information is always correct.

1. Disconnect the battery ground cable.

Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).

2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.

3. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).

4. Using a suitable hydraulic jack, support the transmission.

5. Refer to: Air Cleaner (303-12B Intake Air Distribution and Filtering - GTDi 2.0L Petrol, Removal and Installation).

6. Refer to: Battery Tray (414-01 Battery, Mounting and Cables, Removal and Installation).

7. Torque:

Range Rover Evoque. Engine - GTDi 2.0L Petrol

8. Torque: 175 Nm

Range Rover Evoque. Engine - GTDi 2.0L Petrol

Installation

1. To install, reverse the removal procedure.

Engine Mount RH

Removal

NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).

2. Refer to: Engine Cover - GTDi 2.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

3. Support the engine.

4. Torque: 110 Nm

Range Rover Evoque. Engine - GTDi 2.0L Petrol

5. NOTE: Loosen the bolt, but do not fully remove. Torque: 110 Nm

Range Rover Evoque. Engine - GTDi 2.0L Petrol

6. Torque: 80 Nm

Range Rover Evoque. Engine - GTDi 2.0L Petrol

7. Torque: 80 Nm

Range Rover Evoque. Engine - GTDi 2.0L Petrol

8. NOTE: Do not disassemble further if the component is removed for access only. Torque: 110 Nm

Range Rover Evoque. Engine - GTDi 2.0L Petrol

Installation

1. To install, reverse the removal procedure.

Flexplate

Removal

1. Refer to: Transmission - GTDi 2.0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal).

2.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

Installation

1. CAUTION: Make sure that new bolts are installed.

NOTE: Tighten the retaining bolts in the sequence shown.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

2. Refer to: Transmission - GTDi 2.0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal).

READ NEXT:

 Intake Manifold

Removal NOTES: Removal steps in this procedure may contain installation details. Some illustrations may show the engine removed for clarity. 1. WARNING: Make sure to support the vehicle with axle sta

 Oil Cooler

Removal NOTE: Removal steps in this procedure may contain installation details. 1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle. 2. Disconnect the battery

 Oil Pan

Removal NOTES: Some illustrations may show the engine removed for clarity. Some variation in the illustrations may occur, but the essential information is always correct. Removal steps in this proc

SEE MORE:

 Component Description

DESCRIPTION Engine Control Module (ECM) The ECM is located at the rear of the engine compartment, between the bulkhead and the engine sound insulation. The ECM is located in a plastic molded carrier which in turn is located in a bracket attached to the vehicle structure. The ECM is connected to t

 System Operation

PRINCIPLES OF OPERATION - PARKING AID Vehicles Fitted With Automatic Transmission If reverse ) is the first gear selected after the ignition is switched on, both the front (if fitted) and rear parking aid sensors will become operational. If a forward drive gear is subsequently selected, the front

© 2011-2025 Copyright www.rrevoque.org