Range Rover Evoque: Inner Constant Velocity (CV) Joint Boot
Special Tool(s)
303-D121
Puller, General Purpose
General Equipment
- Vise
Removal
NOTE: RH inner constant velocity joint boot shown, LH is similar.
1. Refer to: Rear Halfshaft LH (205-05 Rear Drive Halfshafts, Removal and Installation).
Refer to: Rear Halfshaft RH (205-05 Rear Drive Halfshafts, Removal and Installation).
2. NOTE: Discard the retaining clips. General Equipment: Vise
3. CAUTION: Make sure that filings and swarf do not enter the component.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
4. NOTE: Discard the retaining clip.
5. Special Tool(s): 303-D121
Installation
1. CAUTION: Extreme cleanliness must be exercised when handling these components. Clean and inspect the components for deterioration.
2.
3. NOTE: Install a new retaining clip.
4. CAUTION: Make sure that these components are installed to the noted removal position.
5. Pack the inner CV joint with the grease supplied.
6. NOTE: Install new retaining clips.
7. Refer to: Rear Halfshaft LH (205-05 Rear Drive Halfshafts, Removal and Installation).
Refer to: Rear Halfshaft RH (205-05 Rear Drive Halfshafts, Removal and Installation).
Outer Constant Velocity (CV) Joint Boot
Special Tool(s)
303-D121
Puller, General Purpose
General Equipment
- Vise
Removal
NOTE: The outer constant velocity joint must not be removed from the shaft. The inner joint and boot have to be removed to allow the outer joint boot to be replaced. The inner and outer boots are supplied together as a kit. RH inner constant velocity joint boot shown, LH is similar.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Rear Halfshaft LH (205-05 Rear Drive Halfshafts, Removal and Installation).
Refer to: Rear Halfshaft RH (205-05 Rear Drive Halfshafts, Removal and Installation).
3. NOTE: Discard the retaining clips. General Equipment: Vise
4. NOTE: Discard the retaining clips.
5.
CAUTION: Make sure that filings and swarf do not enter the component.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
6. NOTE: Discard the retaining clip.
7. Special Tool(s): 303-D121
Installation
1. CAUTION: Extreme cleanliness must be exercised when handling these components. Clean and inspect the components for deterioration.
2.
3. NOTE: Install a new retaining clip.
4. CAUTION: Make sure that these components are installed to the noted removal position.
5. Pack the outer CV joint with the 5. grease supplied.
6. NOTE: Install new retaining clips.
7. Pack the inner CV joint with the grease supplied.
8. NOTE: Install new retaining clips.
9. Refer to: Rear Halfshaft LH (205-05 Rear Drive Halfshafts, Removal and Installation).
Refer to: Rear Halfshaft RH (205-05 Rear Drive Halfshafts, Removal and Installation).
Rear Drive Halfshafts
General Specification
Recommended Lubricant
Torque Specifications
* New nuts/bolts must be installed
READ NEXT:
Brake System - General Information
Brake System Bleeding
CAUTION: Brake fluid will damage paint finished surfaces. If spilled,
immediately remove the fluid and clean the area
with water.
NOTES:
Bleeding of the complete brake system mu
Front Disc Brake
General specifications
Torque Specifications
Brake Pads
Removal
WARNING: Brake pads must be renewed in axle sets only. Failure to follow
this instruction may result in braking
efficiency being impa
SEE MORE:
Headlamps
Moving the nearside headlamp unit to access
bulbs;
1. Remove the two plastic fixings.
2. Pull the tube up to release from the air box.
This will allow more room for
manoeuvrability.
3. Remove the four grille fixings.
4. Remove the two retaining bolts.
5. At the rear of the headlamp unit, p
Head restraints
Adjust the head restraint so
that the
top of the head restraint is above the
centre line of the head. An incorrectly
adjusted head restraint increases the
risk of death or serious injury in the
event of a collision.
Do not drive, or carry passengers with
the head restraints removed from
o
