Range Rover Evoque: Inner Constant Velocity (CV) Joint Boot
Special Tool(s)
303-D121
Puller, General Purpose
General Equipment
- Vise
Removal
NOTE: RH inner constant velocity joint boot shown, LH is similar.
1. Refer to: Front Halfshaft LH (205-04 Front Drive Halfshafts, Removal and Installation).
Refer to: Front Halfshaft RH - LHD AWD/RHD AWD (205-04 Front Drive Halfshafts, Removal and Installation).
Refer to: Front Halfshaft RH - FWD (205-04 Front Drive Halfshafts, Removal and Installation).
2. NOTE: Discard the retaining clips. General Equipment: Vise
3. CAUTION: Make sure that filings and swarf do not enter the component.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
4. NOTE: Discard the retaining clip.
5. Special Tool(s): 303-D121
Installation
1. CAUTION: Extreme cleanliness must be exercised when handling these components. Clean and inspect the components for deterioration.
2.
3. NOTE: Install a new retaining clip.
4. CAUTION: Make sure that these components are installed to the noted removal position.
5. Pack the inner CV joint with the grease supplied.
6. NOTE: Install new retaining clips.
7. Refer to: Front Halfshaft LH (205-04 Front Drive Halfshafts, Removal and Installation).
Refer to: Front Halfshaft RH - LHD AWD/RHD AWD (205-04 Front Drive Halfshafts, Removal and Installation).
Refer to: Front Halfshaft RH - FWD (205-04 Front Drive Halfshafts, Removal and Installation).
Outer Constant Velocity (CV) Joint Boot
General Equipment
- Vise
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Inner Constant Velocity (CV) Joint Boot (205-04 Front Drive Halfshafts, Removal and Installation).
3. NOTE: Discard the retaining clips. General Equipment: Vise
Installation
1. CAUTION: Extreme cleanliness must be exercised when handling these components. Clean and inspect the components for deterioration.
2. Pack the outer CV joint with the grease supplied.
3. NOTES:
Install new retaining clips.
Some variation in the illustrations may occur, but the essential information is always correct.
4. Refer to: Inner Constant Velocity (CV) Joint Boot (205-04 Front Drive Halfshafts, Removal and Installation).
READ NEXT:
Front Halfshaft RH FWD
Special Tool(s)
205-857
Remover, Halfshaft
Removal
CAUTIONS:
Nuts and bolts must be tightened with the weight of the vehicle on the
suspension.
Do not allow halfshafts to hang unsupported at one end
Rear Halfshaft LH
Special Tool(s)
205-857
Remover, Halfshaft
205-928
Remover, Half Shaft Inboard Joint
Removal
CAUTIONS:
Nuts and bolts must be tightened with the weight of the vehicle on the
suspension.
Do not allow
SEE MORE:
Engine Ignition - GTDi 2.0L Petrol
Engine Ignition
Principles of Operation
For a detailed description of the ignition system, refer to the relevant
Description and Operation section in the workshop
manual. REFER to: (303-07D)
Inspection and Verification
CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable.
Subs
Parking aids
Parking aids
1. Parking aid on/off switch. The switch
indicator will illuminate.
When reverse gear is selected, the front
and rear parking sensors are activated
automatically.
To turn off, press the button. The indicator
will extinguish.
2. Approximate sensor range -600mm (24in).
3. Appro
