Range Rover Evoque: Clockspring
Removal
CAUTION: Make sure that the road wheels are in the straight ahead position.
NOTE: Removal steps in this procedure may contain installation details.
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Steering Wheel (211-04 Steering Column, Removal and Installation).
3.
4.
5.
6. CAUTION: Make sure that the clockspring rotor does not rotate. Secure with adhesive tape.
7.
Installation
1. To install, reverse the removal procedure.
2. If a new component is installed, the soft lock stop reset routine should be completed on the power steering system, using the approved diagnostic tool.
Occupant Detection Sensor
Removal
WARNINGS:
To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any air bag supplemental restraint system (SRS) components. To deplete the backup power supply energy, disconnect the battery ground cable and wait one minute. Failure to follow this instruction may result in personal injury.
Never probe the electrical connectors of air bag modules or any other supplemental restraint system component.
Failure to follow this instruction may result in personal injury.
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Front Seat Cushion Cover (501-10 Seating, Removal and Installation).
Vehicles with heated front seats
3.
All vehicles
4.
5.
Installation
1. CAUTION: Make sure the component is aligned as shown.
2. CAUTION: Make sure the component is aligned as shown.
3. To install, reverse the removal procedure.
C-Pillar Side Impact Sensor
Removal
NOTES:
Removal steps in this procedure may contain installation details.
3-door illustration shown, 5-door is similar.
All vehicles
1. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any air bag supplemental restraint system (SRS) components. To deplete the backup power supply energy, disconnect the battery ground cable and wait one minute. Failure to follow this instruction may result in personal injury.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
5-door
2. Refer to: C-Pillar Lower Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
3-door
3. Refer to: Rear Quarter Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
All vehicles
4. Torque: 7 Nm
5. Torque: 10 Nm
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
Front Impact Severity Sensor
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any air bag supplemental restraint system (SRS) components. To deplete the backup power supply energy, disconnect the battery ground cable and wait one minute. Failure to follow this instruction may result in personal injury.
Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Torque: 10 Nm
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
Front Door Side Impact Sensor
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any air bag supplemental restraint system (SRS) components. To deplete the backup power supply energy, disconnect the battery ground cable and wait one minute. Failure to follow this instruction may result in personal injury.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Front Door Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
3. Torque: 1.7 Nm
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
READ NEXT:
Air Bag and Safety Belt Pretensioner
Supplemental Restraint System (SRS)
Principle of Operation
For a detailed description of the supplemental restraints system and
operation, refer to the relevant Description and
Operation section in the workshop manual. REFER to: (501-2
Side Air Bag Module Vehicles With: Sports
Seats
Removal
WARNINGS:
To avoid accidental deployment and possible personal injury, the backup
power supply must be depleted before
repairing or replacing any air bag supplemental restraint system (SRS)
Body Repairs - General Information
General Information
Introduction
The body plays a significant role in the increasing trend of ever more
rapidly changing model variants. The different
customer groups are strongly influenced by the d
SEE MORE:
Engine Wiring Harness TD4 2.2L Diesel, Vehicles With:
M66 6-Speed Manual Transmission AWD/M66 6-Speed Manual
Transmission FWD
Removal
CAUTIONS:
Make sure that the wiring harness is not twisted or damaged on removal. Failure
to follow this instruction may result
in damage to the vehicle.
Take extra care not to damage the wiring harness clips.
NOTES:
Some variation in the illustrations may occur, but the essential informa
Spring Vehicles Without: Dynamic Suspension
Removal
WARNINGS:
Make sure the spring compressor Safe Working Load (SWL) meets or exceeds
the spring rating quoted in the
Specifcations section.
Always follow the spring compressor manufacturer's instructions.
The spring is under extreme tension, care must be taken at all times. Failure to
foll
