Range Rover Evoque: Anti-Lock Control
Torque Specifications
Anti-Lock Brake System (ABS) Module
Removal
CAUTIONS:
If brake fluid is spilt on the paintwork, the affected area must be immediately washed down with cold water.
Make sure that all openings are sealed. Use new blanking caps.
NOTES:
Removal steps in this procedure may contain installation details.
LHD illustration shown, RHD is similar.
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Plenum Chamber (412-01 Climate Control, Removal and Installation).
3. Refer to: Battery Tray (414-01 Battery, Mounting and Cables, Removal and Installation).
Vehicles with petrol engine
4.
Vehicles with diesel engine
5.
All vehicles
6.
7.
8.
9. Torque:
M6 10 Nm
M8 25 Nm
10. WARNING: Fluid loss is unavoidable, use absorbent cloth or a container to collect the fluid. Torque: 17 Nm
11.
12. Torque: 14 Nm
13. Torque: 9 Nm
14. NOTE: Do not disassemble further if the component is removed for access only. Torque: 9 Nm
Installation
1. NOTE: Remove and discard all blanking caps. To install, reverse the removal procedure.
2. Refer to: Brake System Pressure Bleeding (206-00 Brake System - General Information, General Procedures).
3. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
Front Wheel Speed Sensor
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Remove the fender splash shield.
Refer to: Fender Splash Shield (501-02 Front End Body Panels, Removal and Installation).
3.
4. Torque: 5 Nm
Installation
1. CAUTION: Make sure that the mating faces are clean and free of foreign material. To install, reverse the removal procedure.
Rear Wheel Speed Sensor
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
3.
4.
5. Torque: 9 Nm
Installation
1. CAUTIONS:
Make sure that the sensor tip is clean and free of foreign material.
Make sure that the mating faces are clean and free of foreign material.
To install, reverse the removal procedure.
READ NEXT:
Anti-Lock Control - Traction
Control AWD
Component Location
NOTE: RHD (right-hand drive) installations shown; LHD (left-hand drive)
installations similar.
COMPONENT LOCATION - SHEET 1 OF 2
RH (right-hand) front wheel speed sensor
RH rea
Anti-Lock Control - Traction
Control FWD
Component Location
NOTE: RHD (right-hand drive) installations shown; LHD (left-hand drive)
installations similar.
COMPONENT LOCATION - SHEET 1 OF 2
RH (right-hand) front wheel speed sensor
RH rea
SEE MORE:
Topping up the washer fluid
The washer reservoir supplies the front and
rear screen washer jets and headlamp washer
jets.
Check and top-up the reservoir level at least
every week. Always top-up with screen washer
fluid to prevent freezing.
Operate the washer switches periodically to
check that the nozzles are clear and
Battery warning symbols
Do not allow any naked flames,
or other sources of ignition near
the battery as the battery may
emit explosive gasses.
Ensure that when working near,
or handling the battery, suitable
eye protection is worn. This will
reduce the risk of eye damage
caused by acid splashes.
To prevent r
