Range Rover Evoque: Timing Cover
Special Tool(s)
303-021
Engine support bracket
JLR-303-1591
Lifting Bracket, Engine - Rear
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is always correct.
1. Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
4. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
5.
6.
7.
8.
9.
10.
11. Torque: 45 Nm
12. CAUTION: Protect the paintwork during this operation.
13.
14. NOTE: Loosen the bolt, but do not fully remove.
15.
16.
17.
18. NOTE: Make sure that all traces of the old sealant are removed from the mating faces.
Installation
1. CAUTION: Apply sealant WSE-M4G323-A6 in a 4-7mm diameter on the engine front cover as shown.
The component must be installed and tightened within 10 minutes of sealant application.
2. CAUTION: Tighten the bolts in the sequence shown.
Torque:
- M6 10 Nm
- M10 48 Nm
3. Torque: 80 Nm
4. Torque: 80 Nm
5. Torque: 110 Nm
6. NOTE: Loosen the bolt, but do not fully remove. Torque: 110 Nm
7. CAUTION: Protect the paintwork during this operation. Remove the special tool.
Special Tool(s): 303-021
8. Remove the special tool.
Special Tool(s): JLR-303-1591
9. Torque: 6 Nm
10.
11. Torque: 24 Nm
12. Torque: 20 Nm
13. Torque: 25 Nm
14.
15. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
16. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
17. Refer to: Battery (414-01 Battery, Mounting and Cables, Removal and Installation).
READ NEXT:
Valve Cover
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is
always correct.
Removal steps in this proc
Engine - Removal and Installation
Removal
Special Tool(s)
205-857
Remover, Halfshaft
1. Refer to: Battery Tray (414-01 Battery, Mounting and Cables,
Removal and Installation).
2. Refer to: Air Conditioning (A/C) System Recovery, Evacu
Engine Upper/Lower Support Insulator
Engine Upper Support Insulator
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is
always
SEE MORE:
Glass Roof Panel
Removal
CAUTIONS:
Always protect paintwork and glass when removing exterior components.
Always protect the interior components when removing body glass.
Measure all gaps between the glass roof panels before prior to removal to help
aid installation.
Lay the glass on felt covered supports. Do not
Fuel Tank and Lines - Diagnosis and Testing
Principles of Operation
For a detailed description of the fuel tank and lines systems, refer to the
relevant Description and Operation section in the
workshop manual. REFER to: (310-01B Fuel Tank and Lines - GTDi 2.0L Petrol)
Inspection and Verification
WARNINGS:
Eye protection must be worn at all
