Range Rover Evoque: Cylinder Head

Removal

NOTES:

Some illustrations may show the engine removed for clarity.

Some variation in the illustrations may occur, but the essential information is always correct.

1. Refer to: Battery Tray (414-01 Battery, Mounting and Cables, Removal and Installation).

2. Refer to: Cooling System Draining, Filling and Bleeding (303-03B Engine Cooling - GTDi 2.0L Petrol, General Procedures).

3. Refer to: Camshafts (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).

4. Refer to: Intake Manifold (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).

5.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

6. Remove the special tool.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

7.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

8.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

9.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

10.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

11. CAUTION: Using suitable tie straps, make sure the turbocharger assembly is secure.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

12. CAUTIONS:

Make sure that all openings are sealed. Use new blanking caps.

Be prepared to collect escaping coolant.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

13.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

14.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

15.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

16.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

Installation

1.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

2. CAUTION: Apply sealant WSE-M4G323-A6 in a 5-7mm diameter on both cylinder head gasket notches as shown. The cylinder head and engine front cover must be installed and tightened within 30 minutes of sealant application.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

3.

Range Rover Evoque. Engine - GTDi 2.0L Petrol

4. CAUTION: Cylinder head bolts may be reused a maximum of two times only.

NOTE: Tighten the bolts in the indicated sequence.

Torque:

READ NEXT:

 Engine Mount LH/RH

Engine Mount LH Removal NOTES: Removal steps in this procedure may contain installation details. Some variation in the illustrations may occur, but the essential information is always correct. 1. Di

 Intake Manifold

Removal NOTES: Removal steps in this procedure may contain installation details. Some illustrations may show the engine removed for clarity. 1. WARNING: Make sure to support the vehicle with axle sta

 Oil Cooler

Removal NOTE: Removal steps in this procedure may contain installation details. 1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle. 2. Disconnect the battery

SEE MORE:

 Fender Apron Lower Panel

Removal NOTES: The fender apron lower panel is manufactured from mild steel. The panel is serviced less its weld studs This method describes the LH fender apron lower panel, the RH side is similar. 1. The fender apron lower panel is replaced in conjunction with: Front bumper cover Front bumper

 Dab radio controls

Dab radio controls See 104, TOUCH SCREEN OVERVIEW. 1. DAB Radio: Band selection. Touch to view and select a DAB band (DAB 1, 2 or 3). The radio will tune to the last used channel on that band. Touch again to close. The DAB band selection box will close automatically after 5 seconds without

© 2011-2026 Copyright www.rrevoque.org