Range Rover Evoque: Differential Support Insulator
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Support the rear differential using a transmission jack.
3. CAUTION: Mark the components to aid installation.
- Discard the bolts.
4.
Installation
1. Torque: 35 Nm
2. CAUTIONS:
Make sure that new bolts are installed.
Make sure that the installation marks are aligned.
Torque: 175 Nm
Differential Front Bushing
Special Tool(s)
205-860-01
Remover, Differential Bushing
205-860-02
Remover, Differential Bushing
205-860-03
Installer, Differential Bushing
205-860-04
Installer, Differential Bushing
205-860-09
Installer, Differential Bushing
205-860-10
Spacer, Differential Bushing
LR-121
Hydraulic Cylinder 10t
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Remove both rear wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
3. Remove the rear differential.
Refer to: Differential Case - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
4. CAUTIONS:
Mark the components to aid installation.
Note the fitted position of the component prior to removal.
Using the special tools, remove the bushing.
Special Tool(s): 205-860-01, 205-860-02, 205-860-10, LR-121
Installation
1. Using the special tool, compress the bushing.
Special Tool(s): 205-860-09, 205-860-04, LR-121
2. CAUTION: Make sure the correct special tool is used to install the bushings to the correct depth.
NOTE: Make sure that these components are installed to the noted removal position.
Using the special tool, install the bushing.
Special Tool(s): 205-860-10, 205-860-01, 205-860-04, 205-860-03, LR-121
3. Install the rear differential.
Refer to: Differential Case - Vehicles With: M66 6-Speed Manual Transmission AWD (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - Vehicles With: AWF21 6-Speed Automatic Transmission (205-02 Rear Drive Axle/Differential, Removal and Installation).
4. Install the rear wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
READ NEXT:
Differential Rear Bushing
Special Tool(s)
205-860-09
Installer, Differential Bushing
205-861-01
Remover, Differential Bushing
205-861-02
Remover/Installer, Differential Bushing
205-861-03
Installer, Differential Bushing
205-86
Drive Pinion Flange Vehicles With: AWF21
6-Speed Automatic Transmission
Special Tool(s)
205-053
Retainer, Drive Flange
Removal
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
Vehicles with diesel engine
2. Refer t
Drive Pinion Front Bearing
Special Tool(s)
100-012
Slide Hammer
205-067
Preload Gauge
308-615
Remover, Seals
JLR-205-972
Mounting Bracket, Rear Axle
JLR-205-984
Remover/Installer, Drive Pinion Nut
JLR-205-985
Remover, Drive Pin
SEE MORE:
Audio
Front Control Module (ACM) - Low Line
Audio Front Control Module - Low Line (ACM)
CAUTION:
Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution
of control modules does
not guarantee confirmation of a fault, and may also cause additional faults in
the vehicle being tested and/or the donor
vehicle.
Anti-Lock Control
Torque Specifications
Anti-Lock Brake System (ABS) Module
Removal
CAUTIONS:
If brake fluid is spilt on the paintwork, the affected area must be
immediately washed down with cold water.
Make sure that all openings are sealed. Use new blanking caps.
NOTES:
Removal steps in this procedure may contai
