Range Rover Evoque: Transmission Draining and Filling
WARNING: Observe due care when draining, as the fluid can be very hot.
1. WARNING: Make sure to support the vehicle with axle stands.
NOTE: Make sure that the vehicle is standing on a level surface.
Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Be prepared to collect escaping fluids.
Clean the area around the transmission fluid filler plug.
4. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid filler plug.
5. Clean the area around the transmission fluid drain plug.
6. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid drain plug.
7. CAUTION: Make sure that a new sealing washer is installed.
Torque: 30 Nm
8. Use transmission fluid meeting Land Rover specification.
Refer to: Specifications (308-00 Manual Transmission/Transaxle and Clutch - General Information, Specifications).
9. Fill the transmission with the correct fluid until it runs from the filler plug.
10. NOTE: Make sure that a new sealing washer is installed. Torque: 30 Nm
11. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
Transmission Fluid Level Check
WARNING: Observe due care when draining, as the fluid can be very hot.
1. WARNING: Make sure to support the vehicle with axle stands.
NOTE: Make sure that the vehicle is standing on a level surface. Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. Clean the area around the transmission fluid filler plug.
4. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid filler plug.
5. Use transmission fluid meeting Land Rover specification.
Refer to: Specifications (308-00 Manual Transmission/Transaxle and Clutch - General Information, Specifications).
6. Fill the transmission with the correct fluid until it runs from the filler plug.
7. NOTE: Make sure that a new sealing washer is installed. Torque: 30 Nm
8. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
READ NEXT:
Halfshaft Seal RH Vehicles With: M66
6-Speed Manual Transmission AWD
Special Tool(s)
303-1300
Remover, Crankshaft Seal
303-882
Installer, Halfshaft Seal
Removal
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: F
Transmission Vehicles With: M66 6-Speed
Manual Transmission AWD - Removal
Removal
Special Tool(s)
205-857
Remover, Halfshaft
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
General Equipment
Transmission jack
NOTE: Some variation in the
Transmission Vehicles With: M66 6-Speed
Manual Transmission AWD - Installation
Installation
Special Tool(s)
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
NOTE: Some variation in the illustrations may occur, but the essential
information is al
SEE MORE:
Things you need to know
Operate the system only when
it is
safe to do so.
The requirements of national Road Traffic
Regulations always apply.
Observation of traffic signs and local traffic
regulations always take priority.
The navigation system serves solely as an aid
to navigation. In particular, the navigation
Blind spot monitor
The Blind
Spot Monitor (BSM) system
is a supplement to, not a replacement
for, a safe driving style and use of the
exterior and rear-view mirrors.
Please note that BSM may not be able
to give adequate warning of vehicles
approaching very quickly from behind
or vehicles that are being overt
