Range Rover Evoque: Condenser GTDi 2.0L Petrol
Removal
CAUTION: Make sure that all openings are sealed. Use new blanking caps.
NOTES: Some variation in the illustrations may occur, but the essential information is always correct.
Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging - GTDi 2.0L Petrol (412-00 Climate Control System - General Information, General Procedures).
3. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
4. Refer to: Charge Air Cooler (303-12B Intake Air Distribution and Filtering - GTDi 2.0L Petrol, Removal and Installation).
5. Torque: 10 Nm
6. CAUTION: Extreme cleanliness must be exercised when handling these components.
NOTES: Remove and discard the O-ring seals.
Lubricate the O-ring seals with clean refrigerant oil. Torque: 24 Nm
7.
8. CAUTION: Take extra care not to damage the component.
Torque: 5 Nm
9. NOTE: This step is only required if a new component is installed.
Torque: 6 Nm
Installation
1. To install, reverse the removal procedure.
Air Conditioning (A/C) Compressor GTDi 2.0L Petrol
Removal
CAUTION: Make sure that the specified amount of refrigerant oil is added.
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging - GTDi 2.0L Petrol (412-00 Climate Control System - General Information, General Procedures).
4. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
5. Refer to: Accessory Drive Belt (303-05B Accessory Drive - GTDi 2.0L Petrol, Removal and Installation).
6.
7. CAUTIONS: Make sure that all openings are sealed. Use new blanking caps.
Lubricate the new seals with clean refrigerant oil.
NOTE: Install new O-ring seals.
Torque: 24 Nm
8. Torque: 25 Nm
9. NOTE: Loosen the bolt, but do not fully remove.
Torque: 25 Nm
Installation
1. CAUTION: Make sure that the specified amount of refrigerant oil is added.
To install, reverse the removal procedure.
READ NEXT:
Blower Motor LHD AWD/LHD FWD
Special Tool(s)
412-140
Remover/Installer, Blower Motor
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essenti
Blower Motor RHD AWD/RHD FWD, RHD
Special Tool(s)
412-140
Remover/Installer, Blower Motor
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essenti
Climate Control Assembly
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. CAUTION: LH illustration shown, RH is similar.
NOTE: The procedure must be carried out on both
sides.
SEE MORE:
Front Seat Track Motor
Removal
NOTES:
Some variation in the illustrations may occur, but the essential
information is always correct.
Removal steps in this procedure may contain installation details.
1. Raise the front seat to the highest position.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-0
Diesel particulate filter (DPF)
Diesel vehicles equipped with a particulate filter
have more efficient emission control. The
particles in the exhaust gases are collected in
the filter during normal driving.
When a DPF message is displayed, the filter
requires a regeneration cycle to clean itself.
This requires the engine to
