Range Rover Evoque: Heater Core and Evaporator Core Housing
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Instrument Panel - TD4 2.2L Diesel (501-12 Instrument Panel and Console, Removal and Installation).
Refer to: Instrument Panel - GTDi 2.0L Petrol (501-12 Instrument Panel and Console, Removal and Installation).
3.
4. Torque: 1 Nm
5.
6. Torque: 1.5 Nm
7. CAUTION: Take extra care not to damage the instrument cluster face.
8.
9. Torque: 6 Nm
10.
11.
12. Torque: 6 Nm
13. Torque: 6 Nm
14.
15. Torque: 6 Nm
16. NOTE: With assistance remove the component.
Torque: 6 Nm
17.
18.
19. Torque: 6 Nm
20.
21. Torque: 2 Nm
22. NOTE: With assistance remove the component.
Torque: 7 Nm
Installation
1. To install, reverse the removal procedure.
Air Conditioning (A/C) Pressure Transducer
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Plenum Chamber (412-01 Climate Control, Removal and Installation).
2. CAUTIONS: Extreme cleanliness must be exercised when handling these components.
Make sure that all openings are sealed. Use new blanking caps.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
Torque: 8 Nm
Installation
1. To install, reverse the removal procedure.
Temperature Blend Door Actuator LH LHD AWD/LHD FWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Heater Core and Evaporator Core Housing (412-01 Climate Control, Removal and Installation).
3.
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
Temperature Blend Door Actuator RH
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Heater Core and Evaporator Core Housing (412-01 Climate Control, Removal and Installation).
3.
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
READ NEXT:
Defrost Vent/Register Blend Door Actuator LHD AWD/LHD
FWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables,
Specifications).
Desiccant Bag GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: Condenser - G
Control Components FWD - Overview
OVERVIEW
The climate control system incorporates the heating, ventilation and A/C (air
conditioning) systems. There are 2 main
types of climate control system available:
a dual zone automatic syste
SEE MORE:
Temporary spare wheel
Always adhere to the
instructions
given on the temporary use spare
wheel warning label. Failure to
comply can be dangerous.
When a temporary use spare wheel is
fitted, drive with caution and replace
with the specified wheel and tyre as
soon as possible.
Do not fit more than one temporary
Garage door transceiver
Do not use the transceiver
with any
garage door opener that lacks the
safety stop and reverse feature as
required by safety standards.
When programming the transceiver to
a garage door opener or entry gate,
ensure the area is clear. This will
prevent potential harm or damage as
the gate o
