Range Rover Evoque: Transmission Draining and Filling
WARNING: Observe due care when draining, as the fluid can be very hot.
1. WARNING: Make sure to support the vehicle with axle stands.
NOTE: Make sure that the vehicle is standing on a level surface.
Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Be prepared to collect escaping fluids.
Clean the area around the transmission fluid filler plug.
4. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid filler plug.
5. Clean the area around the transmission fluid drain plug.
6. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid drain plug.
7. CAUTION: Make sure that a new sealing washer is installed.
Torque: 30 Nm
8. Use transmission fluid meeting Land Rover specification.
Refer to: Specifications (308-00 Manual Transmission/Transaxle and Clutch - General Information, Specifications).
9. Fill the transmission with the correct fluid until it runs from the filler plug.
10. NOTE: Make sure that a new sealing washer is installed. Torque: 30 Nm
11. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
Transmission Fluid Level Check
WARNING: Observe due care when draining, as the fluid can be very hot.
1. WARNING: Make sure to support the vehicle with axle stands.
NOTE: Make sure that the vehicle is standing on a level surface. Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. Clean the area around the transmission fluid filler plug.
4. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid filler plug.
5. Use transmission fluid meeting Land Rover specification.
Refer to: Specifications (308-00 Manual Transmission/Transaxle and Clutch - General Information, Specifications).
6. Fill the transmission with the correct fluid until it runs from the filler plug.
7. NOTE: Make sure that a new sealing washer is installed. Torque: 30 Nm
8. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
READ NEXT:
Halfshaft Seal RH Vehicles With: M66
6-Speed Manual Transmission AWD
Special Tool(s)
303-1300
Remover, Crankshaft Seal
303-882
Installer, Halfshaft Seal
Removal
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: F
Transmission Vehicles With: M66 6-Speed
Manual Transmission AWD - Removal
Removal
Special Tool(s)
205-857
Remover, Halfshaft
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
General Equipment
Transmission jack
NOTE: Some variation in the
Transmission Vehicles With: M66 6-Speed
Manual Transmission AWD - Installation
Installation
Special Tool(s)
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
NOTE: Some variation in the illustrations may occur, but the essential
information is al
SEE MORE:
Topping up the coolant
Never remove the filler cap
when the
engine is hot - escaping steam or
scalding water could cause serious
personal injury.
Antifreeze is highly inflammable. Do
not allow antifreeze to come into
contact with naked flames or other
sources of ignition (e.g. a hot engine)
- a fire may result.
Steering column lock
During vehicle recovery, a
Smart Key
must remain inside the vehicle, so that
the steering column remains unlocked.
See 216, RECOVERY.
Your vehicle is fitted with an electronic steering
column lock, which locks and unlocks in
conjunction with the vehicle locking system. It
also locks automa
