Range Rover Evoque: Desiccant Bag GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Condenser - GTDi 2.0L Petrol (412-01 Climate Control, Removal and Installation).
3. Torque: 11 Nm
Installation
1. To install, reverse the removal procedure.
Desiccant Bag TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: Condenser - TD4 2.2L Diesel (412-01 Climate Control, Removal and Installation).
3. Torque: 11 Nm
Installation
1. To install, reverse the removal procedure.
Heater Core GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Cooling System Partial Draining, Filling and Bleeding (303-03B Engine Cooling - GTDi 2.0L Petrol, General Procedures).
3. Refer to: Electric Booster Heater (412-02 Auxiliary Climate Control, Removal and Installation).
4. CAUTION: Be prepared to collect escaping coolant.
5.
6. CAUTION: Be prepared to collect escaping coolant.
Installation
1. To install, reverse the removal procedure.
Thermostatic Expansion Valve GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging - GTDi 2.0L Petrol (412-00 Climate Control System - General Information, General Procedures).
3. Refer to: Engine Control Module (ECM) (303-14B Electronic Engine Controls - GTDi 2.0L Petrol, Removal and Installation).
4. CAUTIONS: Make sure that all openings are sealed. Use new blanking caps.
Lubricate the new seals with clean refrigerant oil.
NOTE: Install new O-ring seals.
Torque: 9 Nm
5. Torque: 4 Nm
Installation
1. To install, reverse the removal procedure.
Blower Motor Resistor RHD AWD/RHD FWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. NOTE: LHD illustration shown, RHD is similar.
3. NOTE: LHD illustration shown, RHD is similar.
4.
Installation
1. To install, reverse the removal procedure.
Footwell Vent/Duct Blend Door Actuator RHD AWD/RHD FWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Glove Compartment (501-12 Instrument Panel and Console, Removal and Installation).
3.
4.
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
Temperature Blend Door Actuator LH RHD AWD/RHD FWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Glove Compartment (501-12 Instrument Panel and Console, Removal and Installation).
3.
4.
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
Defrost Vent/Register Blend Door Actuator RHD AWD/RHD FWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Steering Column (211-04 Steering Column, Removal and Installation).
3.
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Land Rover approved diagnostic equipment.
READ NEXT:
Control Components FWD - Overview
OVERVIEW
The climate control system incorporates the heating, ventilation and A/C (air
conditioning) systems. There are 2 main
types of climate control system available:
a dual zone automatic syste
Electric Booster Heater - Description and Operation
Component Location
COMPONENT LOCATION
Heater assembly
Electric booster heater
Overview
OVERVIEW
Due to the slower warm up times associated with the diesel engine, an
electric booster heater may
SEE MORE:
Rear loadspace
Never allow passengers to
travel in
the loadspace under any
circumstances. All vehicle occupants
should be seated correctly and wear a
seat belt at all times when the vehicle
is in motion.
Always ensure that objects carried
within the vehicle are secured
properly.
To remove the loadspa
Front Side Member and Suspension Top Mount
Assembly
Removal
NOTES:
The front side member and suspension top mount assembly consists of the
front side member closing panel, fender apron panel front
reinforcement, fender apron lower panel, suspension top mount, and fender apron
panel reinforcement.
The front side member and suspension top mount is m
