Range Rover Evoque: Transmission Draining and Filling
WARNING: Observe due care when draining, as the fluid can be very hot.
1. WARNING: Make sure to support the vehicle with axle stands.
NOTE: Make sure that the vehicle is standing on a level surface.
Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Be prepared to collect escaping fluids.
Clean the area around the transmission fluid filler plug.
4. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid filler plug.
5. Clean the area around the transmission fluid drain plug.
6. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid drain plug.
7. CAUTION: Make sure that a new sealing washer is installed.
Torque: 30 Nm
8. Use transmission fluid meeting Land Rover specification.
Refer to: Specifications (308-00 Manual Transmission/Transaxle and Clutch - General Information, Specifications).
9. Fill the transmission with the correct fluid until it runs from the filler plug.
10. NOTE: Make sure that a new sealing washer is installed. Torque: 30 Nm
11. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
Transmission Fluid Level Check
WARNING: Observe due care when draining, as the fluid can be very hot.
1. WARNING: Make sure to support the vehicle with axle stands.
NOTE: Make sure that the vehicle is standing on a level surface. Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. Clean the area around the transmission fluid filler plug.
4. CAUTION: Be prepared to collect escaping fluids.
NOTE: Discard the sealing washer.
- Place a container under the transmission.
- Remove the transmission fluid filler plug.
5. Use transmission fluid meeting Land Rover specification.
Refer to: Specifications (308-00 Manual Transmission/Transaxle and Clutch - General Information, Specifications).
6. Fill the transmission with the correct fluid until it runs from the filler plug.
7. NOTE: Make sure that a new sealing washer is installed. Torque: 30 Nm
8. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
READ NEXT:
Halfshaft Seal RH Vehicles With: M66
6-Speed Manual Transmission AWD
Special Tool(s)
303-1300
Remover, Crankshaft Seal
303-882
Installer, Halfshaft Seal
Removal
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: F
Transmission Vehicles With: M66 6-Speed
Manual Transmission AWD - Removal
Removal
Special Tool(s)
205-857
Remover, Halfshaft
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
General Equipment
Transmission jack
NOTE: Some variation in the
Transmission Vehicles With: M66 6-Speed
Manual Transmission AWD - Installation
Installation
Special Tool(s)
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
NOTE: Some variation in the illustrations may occur, but the essential
information is al
SEE MORE:
Glass Roof Panel Blind
Removal
CAUTION: When removing and installing the glass roof panel blind, extreme
cleanliness must be observed at all
times.
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. NOTE: The procedure must be carried out on both sides.
Refer to: A-Pillar Trim Panel
Steering Linkage
Tie Rod End
Special Tool(s)
205-754A
Splitter, Ball Joints
Removal
NOTE: RH illustration shown, LH is similar.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and
Installation).
3.
4. CAUTIO
