Range Rover Evoque: Fuel Tank
Special Tool(s)
310-123
Locking Ring, Fuel Tank
Removal
WARNINGS: Fuel may still be present in the fuel tank after draining.
Avoid flames, sparks or lighted substances.
CAUTIONS: Extreme cleanliness must be exercised when handling these components.
Make sure that all openings are sealed. Use new blanking caps.
NOTES: Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Rear Seat Cushion (501-10 Seating, Removal and Installation).
4. Refer to: Fuel Tank Draining (310-00 Fuel System - General Information, General Procedures).
5. Refer to: Driveshaft - GTDi 2.0L Petrol (205-01 Driveshaft, Removal and Installation).
6.
7.
8.
9. Torque: 5 Nm
10. Torque: 24 Nm
11. CAUTION: Be prepared to collect escaping fuel.
12. NOTE: Using a suitable transmission jack support the differential case.
Torque: 110 Nm
13. CAUTION: Using a suitable transmission jack lower the fuel tank.
Torque: 25 Nm
14. CAUTION: Be prepared to collect escaping fuel.
NOTE: Do not disassemble further if the component is removed for access only.
15.
16. CAUTIONS: Extreme cleanliness must be exercised when handling these components.
Make sure that the seal is correctly positioned.
Failure to follow this instruction may result in damage to the vehicle.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
- Special Tool(s): 310-123
- Torque: 200 Nm
17.
18.
19.
Installation
1. To install, reverse the removal procedure.
Fuel Tank Filler Pipe
Removal
WARNING: Avoid flames, sparks or lighted substances.
CAUTIONS: Extreme cleanliness must be exercised when handling these components.
Make sure that all openings are sealed. Use new blanking caps.
NOTES: Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Remove the rear wheel.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
4.
5. Torque: 10 Nm
6.
7. WARNING: This procedure involves fuel handling.
Be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure to follow these instructions may result in personal injury.
8.
Installation
1. To install, reverse the removal procedure.
READ NEXT:
Fuel Tank and Lines - Diagnosis and Testing
Principles of Operation
For a detailed description of the fuel tank and lines systems, refer to the
relevant Description and Operation section in the
workshop manual. REFER to: (310-01B Fuel Tank and
Speed Control
Speed Control Actuator
Removal
1. Refer to: Accelerator Pedal (310-02 Acceleration Control, Removal
and Installation).
Installation
1. To install, reverse the removal procedure.
Speed Control Deactiv
SEE MORE:
Rear Seat Backrest Cover 5-Door
Removal
NOTES:
This procedure covers the removal and installation of both rear seat
backrests and the LH rear seat backrest cover.
The RH rear seat backrest cover is similar. All notes and cautions must be
followed strictly to avoid any chance of NVH or
failure of the rear seat backrests.
Some v
Cleaning the exterior
Remove any heavy deposits of
mud and
dirt with a hose before washing the
vehicle.
Never aim a hose water jet directly at
the engine air intake, heater air intakes,
body seals or at any components which
may be damaged.
Do not use a high pressure washer or
steam cleaner in the engine
compa
