Range Rover Evoque: Transfer Case Fluid Level Check
CAUTION: The fluid filler plug is not a fluid level plug.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Make sure that the area around the component is clean and free of foreign material.
NOTE: Remove and discard the sealing washer.
4. CAUTION: The fluid filler plug is not a fluid level plug. Fill the transfer case with the recommended fluid.
Refer to: Specifications (308-07B Transfer Case - Vehicles With: AWF21 6-Speed Automatic Transmission/M66 6-Speed Manual Transmission AWD, Specifications).
5. NOTE: Install a new sealing washer. Torque: 35 Nm
6. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
Power Transfer Unit GTDi 2.0L Petrol
Removal
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Air Cleaner Intake Pipe (303-12B Intake Air Distribution and Filtering - GTDi 2.0L Petrol, Removal and Installation).
3. Refer to: Front Halfshaft RH - LHD AWD/RHD AWD (205-04 Front Drive Halfshafts, Removal and Installation).
4. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
5. Torque: 24 Nm
6. CAUTIONS: Mark the position of the driveshaft flange in relation to the drive pinion flange.
To avoid damage to the joint or gaiter, do not allow the driveshaft to hang.
Make sure that the driveshaft is supported with suitable retaining straps.
The component must be aligned with the installation markings.
Torque: 40 Nm
7. CAUTION: Take extra care not to damage the component.
NOTE: LH illustration shown, RH is similar.
8. NOTE: LH illustration shown, RH is similar.
Remove the RH front wheel arch liner.
9. CAUTIONS: Discard the bolt.
Make sure that a new bolt is installed.
Torque:
- Stage 1: 50 Nm
- Stage 2: 180
READ NEXT:
Power Transfer
Unit TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to:
Transfer Case
Connecting Sleeve Seals GTDi 2.0L Petrol
Special Tool(s)
100-012
Slide Hammer
307-594
Installer, Seal
308-005
Remover, Axle oil seal
Removal
NOTE: Some variation in the illustrations may occur, but the essential
information is always correc
Transfer Case
Connecting Sleeve Seals TD4 2.2L Diesel, Vehicles With: AWF21 6-Speed
Automatic Transmission
Special Tool(s)
100-012
Slide Hammer
307-594
Installer, Seal
308-005
Remover, Axle oil seal
Removal
NOTE: Some variation in the illustrations may occur, but the essential
information is always correc
SEE MORE:
Xenon lamps
High voltage is required to
ignite the
gas and metal vapour which are used
to power Xenon lamps. Contact with
this voltage can cause serious injury.
Replacement or maintenance of
Xenon lamps should only be carried
out by suitably qualified personnel.
Xenon lamp units operate at a very
hig
Rear Seat Backrest Cover 5-Door
Removal
NOTES:
This procedure covers the removal and installation of both rear seat
backrests and the LH rear seat backrest cover.
The RH rear seat backrest cover is similar. All notes and cautions must be
followed strictly to avoid any chance of NVH or
failure of the rear seat backrests.
Some v
