Range Rover Evoque: Active On-Demand Coupling Vehicles With: M66 6-Speed Manual Transmission AWD
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise the vehicle on a lift.
2. Remove the exhaust system.
Refer to: Exhaust System (309-00B Exhaust System - TD4 2.2L Diesel, Removal and Installation).
3. CAUTION: Make sure that the driveshaft is supported with suitable retaining straps.
4.
5. CAUTIONS:
Be prepared to collect escaping oil.
Remove and discard the O-ring seal.
Installation
1. CAUTIONS:
Make sure that the area around the component is clean and free of foreign material.
A new O-ring seal is to be installed Lubricate the O-ring seals.
Only use the specified material to lubricate the seals.
Torque: 24 Nm
2.
3. CAUTION: Make sure that new bolts are installed.
NOTE: Tighten the retaining bolts working diagonally. Torque: 40 Nm
4. Check and top-up the active on-demand coupling fluid level.
Refer to: Active On-Demand Coupling Filling (205-02 Rear Drive Axle/Differential, General Procedures).
5. Refer to: Exhaust System (309-00B Exhaust System - TD4 2.2L Diesel, Removal and Installation).
Drive Pinion Flange Vehicles With: M66 6-Speed Manual Transmission AWD
Special Tool(s)
205-053
Retainer, Drive Flange
Removal
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Exhaust System (309-00B Exhaust System - TD4 2.2L Diesel, Removal and Installation).
3. CAUTION: Make sure that the driveshaft is supported with suitable retaining straps.
4. CAUTIONS:
Discard the nut.
Be prepared to collect escaping oil.
- Special Tool(s): 205-053
Installation
1. WARNING: Make sure that a new nut is installed.
- Special Tool(s): 205-053
- Torque: 130 Nm
2. CAUTION: Make sure that new bolts are installed.
NOTE: Tighten the retaining bolts working diagonally. Torque: 40 Nm
3. Check and top-up the active on-demand coupling fluid level.
Refer to: Active On-Demand Coupling Filling (205-02 Rear Drive Axle/Differential, General Procedures).
4. Refer to: Exhaust System (309-00B Exhaust System - TD4 2.2L Diesel, Removal and Installation).
READ NEXT:
Differential Case Vehicles With: M66 6-Speed
Manual Transmission AWD
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Remove the LH rear whee
Front Halfshaft LH
Special Tool(s)
205-857
Remover, Halfshaft
Removal
CAUTIONS:
Nuts and bolts must be tightened with the weight of the vehicle on the
suspension.
Do not allow halfshafts to hang unsupported at one end
SEE MORE:
Body Repairs - Vehicle Specific Information and Tolerance Checks
Body
and Frame
Front End Body Dimensions
NOTES:
All dimensions shown are in millimetres (mm).
Dimensions shown to holes, are always taken from/to the hole centre. They are
also always to the body panel
surface, not to the top of bolts or components.
Side Panel Dimensions
3-door version
5-d
Fuel filler
When refuelling ensure that
all
windows, doors, and sunroof are fully
closed, particularly if young children
or animals are in the vehicle.
Do not attempt to fill the tank to its
maximum capacity. If the vehicle is to
be parked on a slope, in direct
sunlight, or high ambient
temperature,
