Range Rover Evoque: Torque Converter Seal TD4 2.2L Diesel
Special Tool(s)
307-597
Installer, Torque Converter Seal
307-613
Holding Pins, Torque Converter
Removal
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Transmission - TD4 2.2L Diesel (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal).
4. CAUTIONS:
Be prepared to collect escaping oil.
Make sure that all openings are sealed.
- Special Tool(s): 307-613
5. CAUTION: Take extra care when removing the component, prevent damage to the mating faces.
Installation
1. CAUTIONS:
Extreme cleanliness must be exercised when handling this component.
Make sure that the mating faces are clean and free of foreign material.
Special Tool(s): 307-597
2. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Take extra care when handling the component.
Align the torque converter and oil pump drive before installing the torque converter.
Make sure the torque converter is fully located into the oil pump drive.
- Special Tool(s): 307-613
3. Refer to: Transmission - TD4 2.2L Diesel (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Installation).
4. Connect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
Torque Converter TD4 2.2L Diesel
Special Tool(s)
307-613
Holding Pins, Torque Converter
Removal
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Transmission - TD4 2.2L Diesel (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal).
4. CAUTIONS:
Be prepared to collect escaping oil.
Make sure that all openings are sealed.
- Special Tool(s): 307-613
Installation
1. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Take extra care when handling the component.
Align the torque converter and oil pump drive before installing the torque converter.
Make sure the torque converter is fully located into the oil pump drive.
- Special Tool(s): 307-613
2. Refer to: Transmission - TD4 2.2L Diesel (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Installation).
3. Connect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
Input Shaft Speed (ISS) Sensor TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Transmission Fluid Pan - TD4 2 2L Diesel (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal and Installation).
4. CAUTION: Extreme cleanliness must be exercised when handling this component. Torque: 6 Nm
Installation
1. To install, reverse the removal procedure.
READ NEXT:
Transmission Fluid Pan TD4 2.2L Diesel
Removal
CAUTION: Extreme cleanliness must be exercised when handling this
component.
NOTE: Some variation in the illustrations may occur, but the essential
information is always correct.
1. WARNING
Transmission TD4 2.2L Diesel - Removal
Removal
Special Tool(s)
205-857
Remover, Halfshaft
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
General Equipment
Transmission jack
NOTE: Some variation in the
Transmission TD4 2.2L Diesel - Installation
Installation
Special Tool(s)
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
NOTE: Some variation in the illustrations may occur, but the essential
information is al
SEE MORE:
Drive selector
P should normally be selected before switching
off the engine. If any other gear is selected at
turn off, the selector will move to P before
retracting into the centre console.
If the engine is switched off with N selected, the
system will wait for 10 minutes before
selecting P. This time dela
Electric
Power Assisted Steering Module (EPAS)
Steering Gear (PSCM)
CAUTION:
Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution
of control modules does
not guarantee confirmation of a fault, and may also cause additional faults in
the vehicle being tested and/or the donor
vehicle.
NOTES:
If the control
