Range Rover Evoque: Electric Booster Heater - Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
Vehicles with automatic transmission
2. Refer to: Floor Console (501-12 Instrument Panel and Console, Removal and Installation).
Vehicles with manual transmission
3. Refer to: Gearshift Lever (308-06 Manual Transmission/Transaxle External Controls, Removal and Installation).
All vehicles
4.
5.
6. Torque: 2 Nm
Installation
1. To install, reverse the removal procedure.
Fuel Fired Booster Heater GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications)
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Cooling System Partial Draining, Filling and Bleeding (303-03B Engine Cooling - GTDi 2.0L Petrol, General Procedures).
4. Remove the RH fender splash shield.
Refer to: Fender Splash Shield (501-02 Front End Body Panels, Removal and Installation).
5. Torque: 10 Nm
6. CAUTIONS: Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
- Position a container to collect spillage.
- Disconnect the 2 coolant hoses.
- Disconnect the fuel line.
7. Torque: 10 Nm
8.
Installation
1. To install, reverse the removal procedure.
Fuel Fired Booster Heater Coolant Pump GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Secondary Bulkhead Center Panel - GTDi 2.0L Petrol (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Be prepared to collect escaping coolant.
NOTE: Make sure that all openings are sealed.
Use new blanking caps. Clamp the hoses to minimize coolant loss.
4. Torque: 8 Nm
Installation
1. To install, reverse the removal procedure.
2. Check and top-up the coolant if required.
Fuel Fired Booster Heater Glow Plug And Burner Assembly GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Fuel Fired Booster Heater - GTDi 2.0L Petrol (412-02 Auxiliary Climate Control, Removal and Installation).
4. Torque: 10 Nm
5.
6.
7. Torque: 7.5 Nm
8. Torque: 10 Nm
9.
10.
11.
12.
13. Torque: 7 Nm
Installation
1. To install, reverse the removal procedure.
Fuel Fired Booster Heater TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Cooling System Partial Draining, Filling and Bleeding (303-03A Engine Cooling - TD4 2.2L Diesel, General Procedures).
4. Remove the RH fender splash shield.
Refer to: Fender Splash Shield (501-02 Front End Body Panels, Removal and Installation).
5. Torque: 10 Nm
6. CAUTIONS: Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
- Position a container to collect spillage.
- Disconnect the 2 coolant hoses.
- Disconnect the fuel line.
7. Torque: 10 Nm
8.
Installation
1. To install, reverse the removal procedure.
Fuel Fired Booster Heater Fuel Pump
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. WARNING: Be prepared to collect escaping fuel.
CAUTION: Make sure that all openings are sealed.
Use new blanking caps.
4. Torque: 10 Nm
5. NOTE: Do not disassemble further if the component is removed for access only.
Installation
1. To install, reverse the removal procedure.
Fuel Fired Booster Heater Coolant Pump TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. Refer to: Secondary Bulkhead Center Panel - TD4 2.2L Diesel (501-02 Front End Body Panels, Removal and Installation).
3. CAUTION: Be prepared to collect escaping coolant.
NOTE: Make sure that all openings are sealed.
Use new blanking caps. Clamp the hoses to minimize coolant loss.
4. Torque: 8 Nm
Installation
1. To install, reverse the removal procedure.
2. Check and top-up the coolant if required.
Fuel Fired Booster Heater Glow Plug And Burner Assembly TD4 2.2L Diesel
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Fuel Fired Booster Heater - TD4 2.2L Diesel (412-02 Auxiliary Climate Control, Removal and Installation).
4. Torque: 10 Nm
5.
6.
7. Torque: 7.5 Nm
8. Torque: 10 Nm
9.
10.
11.
12.
13. Torque: 7 Nm
Installation
1. To install, reverse the removal procedure.
Fuel Fired Booster Heater Receiver Unit
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Parking Aid Module (413-13 Parking Aid, Removal and Installation).
2.
Installation
1. To install, reverse the removal procedure.
READ NEXT:
Fuel Fired Booster Heater FWD
Component
Location
COMPONENT LOCATION - VEHICLES WITHOUT FFBH REMOTE CONTROL
ATC (automatic temperature control) module
Fuel Fired Booster Heater (FFBH)
Auxiliary coolant pump
Ambient air temper
Instrument Cluster
Instrument Cluster - Component Location
COMPONENT LOCATION
Instrument Cluster - Overview
OVERVIEW
The instrument cluster comprises two analogue gages for the speedometer and
the tachometer and a 5 i
SEE MORE:
Topping up the engine oil
Your vehicle warranty may be
invalidated if damage is caused by
using oil that does not meet the
required specification.
Failure to use an oil that meets the
required specification could cause
excessive engine wear, a build up of
sludge and deposits, and increase
pollution. It could also le
Engine System - General Information
Cylinder Head Gasket Selection TD4
2.2L Diesel
Special Tool(s)
303-979
Measuring Bridge, Piston Protusion
1. CAUTION: Make sure that the surface is clean and
free of foreign material.
Zero the gauge on the cylinder block machined face.
Special Tool(s): 303-979
2. CAUTION: Make sure that the surfac
