Range Rover Evoque: Spring Vehicles Without: Dynamic Suspension
Removal
WARNINGS:
Make sure the spring compressor Safe Working Load (SWL) meets or exceeds the spring rating quoted in the Specifcations section.
Always follow the spring compressor manufacturer's instructions.
The spring is under extreme tension, care must be taken at all times. Failure to follow these instuctions may result in personal injury.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Rear Shock Absorber - Vehicles Without: Dynamic Suspension (204-02 Rear Suspension, Removal and Installation).
3.
4. Inspect the component and install a new one if damaged.
Installation
1. Make sure the correct vehicle suspension components are installed.
Refer to: Specifications (204-00 Suspension System - General Information, Specifications).
2. CAUTIONS:
Make sure the component is aligned as shown.
The spring and isolator must be installed as a pair. Make sure that the correct spring and isolator are fitted according to the vehicle specifications.
3. CAUTION: Make sure that the spring is installed to the damper assembly with the paint marks (located on the spring) at the top.
4. Refer to: Rear Shock Absorber - Vehicles Without: Dynamic Suspension (204-02 Rear Suspension, Removal and Installation).
5. Check the suspension system ride height.
Spring Vehicles With: Dynamic Suspension
Removal
WARNINGS:
Make sure the spring compressor Safe Working Load (SWL) meets or exceeds the spring rating quoted in the Specifcations section.
Always follow the spring compressor manufacturer's instructions.
The spring is under extreme tension, care must be taken at all times. Failure to follow these instuctions may result in personal injury.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Rear Shock Absorber - Vehicles With: Dynamic Suspension (204-02 Rear Suspension, Removal and Installation).
3.
4. Inspect the component and install a new one if damaged.
Installation
1. Make sure the correct vehicle suspension components are installed.
Refer to: Specifications (204-00 Suspension System - General Information, Specifications).
2. CAUTIONS:
Make sure the component is aligned as shown.
The spring and isolator must be installed as a pair.
Make sure that the correct spring and isolator are fitted according to the vehicle specifications.
3. CAUTION: Make sure that the spring is installed to the damper assembly with the paint marks (located on the spring) at the top.
4. Refer to: Rear Shock Absorber - Vehicles With: Dynamic Suspension (204-02 Rear Suspension, Removal and Installation).
5. Check the suspension system ride height.
READ NEXT:
Rear Lower Arm FWD
Removal
NOTES:
LH illustration shown, RH is similar.
Some variation in the illustrations may occur, but the essential information is
always correct.
1. WARNING: Make sure to support the vehicle with
Rear Suspension FWD
Component Location
Stabilizer link
RH (right-hand) spring and damper assembly
Stabilizer bar
LH (left-hand) spring and damper assembly
Wheel knuckle
Stub axle and locknut
Hub
Longitudinal li
Wheels and Tires
Wheel and Tire
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. NOTE: Ma
SEE MORE:
Vehicle Transportation Aids and Vehicle Storage
New Vehicle Storage
INTRODUCTION
Standards
Vehicles may require storage for varying periods of time before the customer
takes delivery. It is essential that a new Land
Rover vehicle is stored correctly, in order to ensure total customer
satisfaction after the car is removed from storage and
prepar
Start guidance
After touching Destination, the system will
calculate the route.
There is now a choice to select 3 Routes,
Change route or to Start navigation guidance.
Touch 3 Routes to display a choice of three
different route options on the map.
The roads on the map are drawn in three
different colours to
