Range Rover Evoque: Rear Shock Absorber Vehicles Without: Dynamic Suspension
General Equipment
- Suspension Spring Compressor
- Vise
Removal
WARNINGS:
Make sure the spring compressor Safe Working Load (SWL) meets or exceeds the spring rating quoted in the Specifcations section.
Always follow the spring compressor manufacturer's instructions.
The spring is under extreme tension, care must be taken at all times. Failure to follow these instuctions may result in personal injury.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Shock Absorber and Spring Assembly - Vehicles Without: Dynamic Suspension (204-02 Rear Suspension, Removal and Installation).
3.
4. CAUTION: Mark the components to aid installation.
5.
- General Equipment: Suspension Spring Compressor
- General Equipment: Vise
6.
7.
8. WARNING: Make sure to support the shock absorber.
CAUTION: Discard the nut.
9.
10.
Installation
1. Make sure the correct vehicle suspension components are installed.
Refer to: Specifications (204-00 Suspension System - General Information, Specifications).
2. Inspect the component and install a new one if damaged.
3. Inspect the component and install a new one if damaged.
4. Inspect the component and install a new one if damaged.
5. CAUTION: Make sure the component is aligned as shown.
NOTE: Make sure that the component is installed to the position noted on removal. Inspect the component and install a new one if damaged.
6. Inspect the component and install a new one if damaged.
7. Inspect the component and install a new one if damaged.
8. CAUTION: Make sure the component is aligned as shown.
- Inspect the component and install a new one if damaged.
- Make sure that the correct spring and isolator are fitted according to the vehicle specifications.
9.
10. WARNING: Make sure to support the shock absorber.
CAUTIONS:
Make sure the component is aligned as shown.
Make sure that the spring is installed to the damper assembly with the paint marks (located on the spring) at the top.
11. WARNINGS:
Make sure that a new nut is installed.
Make sure to support the shock absorber.
Torque: 67 Nm
12.
13. CAUTION: Make sure the components are aligned as shown.
14.
15.
16. CAUTION: Make sure the components are aligned as shown.
17. CAUTION: Make sure the components are aligned as shown.
18. Refer to: Shock Absorber and Spring Assembly - Vehicles Without: Dynamic Suspension (204-02 Rear Suspension, Removal and Installation).
19. Check the suspension system ride height.
READ NEXT:
Shock Absorber and Spring Assembly Vehicles Without:
Dynamic Suspension
Special Tool(s)
JLR-204-804
Lever, Wheel Knuckle
General Equipment
Transmission jack
Wooden Block
CAUTIONS:
Nuts and bolts must be tightened with the weight of the vehicle on the
suspension.
LH
Wheel Knuckle Rear Bushing
Special Tool(s)
204-620-01
Installer, Wheel Knuckle Bushing
204-620-02
Remover/Installer, Wheel Knuckle Bushing
204-620-03
Remover, Wheel Knuckle Bushing
LR-121
Hydraulic Cylinder 10t
Removal
1. WARNI
Rear Shock Absorber Vehicles With: Dynamic
Suspension
General Equipment
Suspension Spring Compressor
Vise
Removal
WARNINGS:
Make sure the spring compressor Safe Working Load (SWL) meets or exceeds
the spring rating quoted in the
Specifcations sectio
SEE MORE:
Powered tailgate opening height
The maximum opening height can be set as
required. This is useful in parking areas with
low ceiling heights or just for ease of use.
1. Open the tailgate to the position which you
want to set as the maximum height. Press
any tailgate control to stop movement at
the required position. Final pos
Dual view control menu
Dual view control menu
1. Select to cancel dual view and revert to the
menu for the current video source (TV,
DVD).
Note: The preview screen will be
deactivated if the vehicle is moving.
2. Select to view a list of all available video
sources. Touch the relevant soft key to
select an alter
