Range Rover Evoque manuals

Range Rover Evoque: Catalyst Monitor Sensor

Land Rover Range Rover Evoque L538 (2011–2018) Service Manual / Engine / Electronic Engine Controls - GTDi 2.0L Petrol / Catalyst Monitor Sensor

Special Tool(s)

310-121
Wrench, H02S

Removal

WARNING: Observe due care when working near a hot exhaust system.

NOTE: Removal steps in this procedure may contain installation details.

1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.

2. Disconnect the battery ground cable.

Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).

3. Refer to: Engine Cover - GTDi 2.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

4.

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

5.

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

6. Torque:

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

7.

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

8. CAUTIONS:

Make sure that the mating faces are clean and free of corrosion and foreign material.

Note the fitted position of the component prior to removal.

Special Tool(s): 310-121

Torque: 48 Nm

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

Installation

1. CAUTIONS:

If accidentally dropped or knocked install a new sensor.

Make sure the HO2S wiring harness is not twisted more than 180 degrees and is not in contact with either the exhaust or driveshaft.

Make sure the anti-seize compound does not contact the heated oxygen sensor (HO2S) tip.

NOTE: If the original sensor is to be installed, apply lubricant meeting specification ESE-M12A4-A to the thread of the sensor.

To install, reverse the removal procedure.

Front Knock Sensor (KS)

Removal

NOTE: Removal steps in this procedure may contain installation details.

1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.

2. Refer to: Intake Manifold (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).

3. CAUTION: Note the fitted position of the component prior to removal.

NOTE: Make sure that the component is installed to the noted removal position.

Torque: 20 Nm

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

Installation

1. To install, reverse the removal procedure.

Rear Knock Sensor (KS)

Removal

NOTE: Removal steps in this procedure may contain installation details.

1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.

2. Refer to: Intake Manifold (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).

3. CAUTION: Note the fitted position of the component prior to removal.

NOTE: Make sure that the component is installed to the noted removal position. Torque: 20 Nm

Range Rover Evoque. Electronic Engine Controls - GTDi 2.0L Petrol

Installation

1. To install, reverse the removal procedure.

READ NEXT:

 Electronic Engine Controls

Principles of Operation For a detailed description of the 2.0L GTDi petrol electronic engine controls, refer to the relevant Description and Operation section in the workshop manual. REFER to: (303-1

 Automatic Transmission & Transaxle

 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission

SEE MORE:

 Gear shift indicator

The gear shift indicator illuminates briefly at the recommended gear change point (upshift). The shift indicator will not illuminate while Cruise control is active and is not being overridden by pressing the throttle pedal. Note: This warning indicator is only a guide. It remains the respo

 Wipers and Washers - Removal and Installation

Windshield Wiper Motor Removal NOTE: Removal steps in this procedure may contain installation details. 1. Refer to: Plenum Chamber (412-01 Climate Control, Removal and Installation). 2. NOTE: LHD illustration shown, RHD is similar. Torque: 8 Nm Installation 1. To install, reverse the removal proced

© 2011-2025 Copyright www.rrevoque.org