Range Rover Evoque: Engine Timing
Special Tool(s)
303-1565
Locking Tool, Camshaft
308-511
Installer, Transmission Output Shaft Seal
JLR-303-1594
Locking Tool, Driveplate
JLR-303-748
Locking Tool, Crankshaft
Activation
1.
2. Install the special tool.
Special Tool(s): JLR-303-748
3. Rotate the engine clockwise until the crankshaft stops against the special tool as indicated.
4. CAUTION: Make sure that new bolts are installed. Install all the bolts finger tight before final tightening.
5. Install the special tool.
Special Tool(s): JLR-303-1594
6. NOTE: Tighten the retaining bolts in the sequence shown.
Torque:
- Stage 1: 50 Nm
- Stage 2: 80 Nm
- Stage 3: 112 Nm
7. CAUTION: Note the orientation of the crankshaft sprocket.
NOTE: Install but do not tighten fixing at this stage.
8. Rotate the engine until the trigger wheel gap and camshafts are positioned as indicated.
9. Install the special tool.
Special Tool(s): 303-1565
10. CAUTION: Make sure new washers are installed.
11. CAUTIONS:
Use an open-ended wrench to hold the camshafts by the hexagon to prevent the camshafts from turning.
Make sure that these components are installed to the noted removal position.
Only tighten the bolts finger-tight at this stage.
12.
13. Torque: 9 Nm
14. Torque: 9 Nm
15. CAUTION: Use an open-ended wrench to hold the camshafts by the hexagon to prevent the camshafts from turning. Torque: 72 Nm
16. CAUTION: Using a suitable tool, hold the oil pump gear when installing the centre bolt. Torque: 25 Nm
17. CAUTION: Apply sealant WSE-M4G323-A6 in a 4-7mm diameter on the engine front cover as shown.
The component must be installed and tightened within 10 minutes of sealant application.
18. CAUTION: Tighten the bolts in the sequence shown.
Torque:
- M6 10 Nm
- M10 48 Nm
19. Special Tool(s): 308-511
20. CAUTIONS:
Only tighten the bolt finger-tight at this stage.
Make sure that the mating faces are clean and free of foreign material.
NOTE: Apply WSS-M2C913-B or WSS-M2C913-C oil on the damper sealing surface prior to installation.
21. CAUTION: Rotate the crankshaft damper to align special tool 303-1595. Do not rotate the crankshaft. Install the special tool
22. Remove the special tool
23.
Torque:
- Stage 1: 100 Nm
- Stage 2: 90
READ NEXT:
Engine Cooling - Component Location, System Operation and
Component Description
Component Location
COMPONENT LOCATION
Heater core
Air Conditioning (A/C) Evaporator (ref only)
Heater inlet hose
Heater outlet hose/Oil cooler inlet hose
Turbocharger water outlet pipe
Water o
Cooling System Draining, Filling and
Bleeding
Draining
CAUTIONS:
The engine cooling system must be maintained with the correct
concentration and type of anti-freeze solution to
prevent corrosion and frost damage. Failure to follow this instructi
SEE MORE:
Differential Case Vehicles With: AWF21
6-Speed Automatic Transmission
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Remove the LH rear wheel and tire.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and
Installati
Electric parking brake (EPD)
The parking brake operates on
the rear
wheels. Therefore, secure parking of
the vehicle is dependent on being on a
hard and stable surface.
Do not rely on the parking brake to
operate effectively, if the rear wheels
have been immersed in mud or water.
Note: If the vehicle is used in severe
