Range Rover Evoque: Timing Cover
Special Tool(s)
303-021
Engine support bracket
JLR-303-1591
Lifting Bracket, Engine - Rear
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is always correct.
1. Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
4. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
5.
6.
7.
8.
9.
10.
11. Torque: 45 Nm
12. CAUTION: Protect the paintwork during this operation.
13.
14. NOTE: Loosen the bolt, but do not fully remove.
15.
16.
17.
18. NOTE: Make sure that all traces of the old sealant are removed from the mating faces.
Installation
1. CAUTION: Apply sealant WSE-M4G323-A6 in a 4-7mm diameter on the engine front cover as shown.
The component must be installed and tightened within 10 minutes of sealant application.
2. CAUTION: Tighten the bolts in the sequence shown.
Torque:
- M6 10 Nm
- M10 48 Nm
3. Torque: 80 Nm
4. Torque: 80 Nm
5. Torque: 110 Nm
6. NOTE: Loosen the bolt, but do not fully remove. Torque: 110 Nm
7. CAUTION: Protect the paintwork during this operation. Remove the special tool.
Special Tool(s): 303-021
8. Remove the special tool.
Special Tool(s): JLR-303-1591
9. Torque: 6 Nm
10.
11. Torque: 24 Nm
12. Torque: 20 Nm
13. Torque: 25 Nm
14.
15. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
16. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
17. Refer to: Battery (414-01 Battery, Mounting and Cables, Removal and Installation).
READ NEXT:
Valve Cover
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is
always correct.
Removal steps in this proc
Engine - Removal and Installation
Removal
Special Tool(s)
205-857
Remover, Halfshaft
1. Refer to: Battery Tray (414-01 Battery, Mounting and Cables,
Removal and Installation).
2. Refer to: Air Conditioning (A/C) System Recovery, Evacu
Engine Upper/Lower Support Insulator
Engine Upper Support Insulator
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is
always
SEE MORE:
Using the touch screen
Always run the engine during
prolonged
use of the touch screen. Failure to do so
may discharge the vehicle battery,
preventing the engine from starting.
Avoid spilling or splashing liquids onto
the touch screen.
Switching on
- Switch on the ignition.
- Switch on the touch screen.
The mos
Power Liftgate Switch, Liftgate
Power Liftgate Switch
Removal
NOTE: Removal steps in this procedure may contain installation details.
1.
2. Torque: 4 Nm
3. Torque: 4 Nm
4.
Installation
1. To install, reverse the removal procedure.
Liftgate
Removal
CAUTION: The headliner must be lowered as a complete unit to gain access
to the
