Range Rover Evoque: Timing Cover
Special Tool(s)
303-021
Engine support bracket
JLR-303-1591
Lifting Bracket, Engine - Rear
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is always correct.
1. Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
2. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
3. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
4. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
5.
6.
7.
8.
9.
10.
11. Torque: 45 Nm
12. CAUTION: Protect the paintwork during this operation.
13.
14. NOTE: Loosen the bolt, but do not fully remove.
15.
16.
17.
18. NOTE: Make sure that all traces of the old sealant are removed from the mating faces.
Installation
1. CAUTION: Apply sealant WSE-M4G323-A6 in a 4-7mm diameter on the engine front cover as shown.
The component must be installed and tightened within 10 minutes of sealant application.
2. CAUTION: Tighten the bolts in the sequence shown.
Torque:
- M6 10 Nm
- M10 48 Nm
3. Torque: 80 Nm
4. Torque: 80 Nm
5. Torque: 110 Nm
6. NOTE: Loosen the bolt, but do not fully remove. Torque: 110 Nm
7. CAUTION: Protect the paintwork during this operation. Remove the special tool.
Special Tool(s): 303-021
8. Remove the special tool.
Special Tool(s): JLR-303-1591
9. Torque: 6 Nm
10.
11. Torque: 24 Nm
12. Torque: 20 Nm
13. Torque: 25 Nm
14.
15. Refer to: Valve Cover (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
16. Refer to: Crankshaft Pulley (303-01B Engine - GTDi 2.0L Petrol, Removal and Installation).
17. Refer to: Battery (414-01 Battery, Mounting and Cables, Removal and Installation).
READ NEXT:
Valve Cover
Removal
NOTES:
Some illustrations may show the engine removed for clarity.
Some variation in the illustrations may occur, but the essential information is
always correct.
Removal steps in this proc
Engine - Removal and Installation
Removal
Special Tool(s)
205-857
Remover, Halfshaft
1. Refer to: Battery Tray (414-01 Battery, Mounting and Cables,
Removal and Installation).
2. Refer to: Air Conditioning (A/C) System Recovery, Evacu
Engine Upper/Lower Support Insulator
Engine Upper Support Insulator
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is
always
SEE MORE:
Smart key check
If the ignition is on or the engine is running and
there is no Smart Key inside the vehicle when
the last door is closed, the message Smart Key
Not Found Refer to Handbook will be displayed
in the message centre.
Ensure that the Smart Key is in the
vehicle before it is driven to another
loca
Solvents, Sealants and Adhesives
Solvents
WARNING: Always
handle all solvents, sealers and adhesives with extreme care. Some contain
chemicals or give off
fumes which can be dangerous to health. Always follow the manufacturers
instructions. If in doubt about any substance,
particularly a solvent, DO NOT use it.
CAUTION: If in
