Range Rover Evoque: Torque Converter Seal GTDi 2.0L Petrol
Special Tool(s)
307-597
Installer, Torque Converter Seal
307-613
Holding Pins, Torque Converter
Removal
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Transmission - GTDi 2.0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal).
4. CAUTIONS:
Be prepared to collect escaping oil.
Make sure that all openings are sealed.
- Special Tool(s): 307-613
5. CAUTION: Take extra care when removing the component, prevent damage to the mating faces.
Installation
1. CAUTIONS:
Extreme cleanliness must be exercised when handling this component.
Make sure that the mating faces are clean and free of foreign material.
- Special Tool(s): 307-597
2. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Take extra care when handling the component.
Align the torque converter and oil pump drive before installing the torque converter.
Make sure the torque converter is fully located into the oil pump drive.
- Special Tool(s): 307-613
3. Refer to: Transmission - GTDi 2.0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Installation).
4. Connect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
Torque Converter GTDi 2.0L Petrol
Special Tool(s)
307-613
Holding Pins, Torque Converter
Removal
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Transmission - GTDi 2.0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal).
4. CAUTIONS:
Be prepared to collect escaping oil.
Make sure that all openings are sealed.
- Special Tool(s): 307-613
Installation
1. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Take extra care when handling the component.
Align the torque converter and oil pump drive before installing the torque converter.
Make sure the torque converter is fully located into the oil pump drive.
- Special Tool(s): 307-613
2. Refer to: Transmission - GTDi 2.0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Installation).
3. Connect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
Input Shaft Speed (ISS) Sensor GTDi 2.0L Petrol
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables, Specifications).
3. Refer to: Transmission Fluid Pan - GTDi 2 0L Petrol (307-01 Automatic Transmission/Transaxle - Vehicles With: AWF21 6-Speed Automatic Transmission, Removal and Installation).
4. CAUTION: Extreme cleanliness must be exercised when handling this component. Torque: 6 Nm
Installation
1. To install, reverse the removal procedure.
READ NEXT:
Transmission GTDi 2.0L Petrol - Removal
Special Tool(s)
205-857
Remover, Halfshaft
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
JLR-303-1591
Lifting Bracket, Engine - Rear
General Equipment
Transmissio
Transmission GTDi 2.0L Petrol - Installation
Installation
NOTE: Some variation in the illustrations may occur, but the essential
information is always correct.
1. NOTE: This step is only required if previously removed.
Torque: 12 Nm
2. NOTE:
Transmission Control Module (TCM) TD4 2.2L
Diesel
Removal
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables,
Specifications).
2. Refer to: Air Cleaner (303-12, Removal and Installation).
3.
4.
5
SEE MORE:
Engine Cooling - Component Location, System Operation and
Component Description
Component Location
COMPONENT LOCATION
Heater core
Air Conditioning (A/C) Evaporator (ref only)
Heater inlet hose
Heater outlet hose/Oil cooler inlet hose
Turbocharger water outlet pipe
Water outlet
Transmission fluid cooler
Electric cooling fan - Left Hand (LH)
Radiator top hose
By-pass
Power Steering AWD
Component Location
Steering gear
Rubber seal assembly
Heat shield
Overview
The vehicle is fitted with EPS (electric power steering), provided by a ZF
Servolectric steering gear unit with variable
ratio, rack and pinion steering and speed sensitive power assistance. Power
assistance is from a
