Range Rover Evoque: Moon roof

Use the overhead switches to open and close the moon roof and tilt it up and down.

Operating the moon roof

■ Opening and closing

Opening and closing the windows

  1. Opens the moon roof*

The moon roof stops slightly before the fully open position to reduce wind noise. Press the switch again to fully open the moon roof.

  1. Closes the moon roof*

*: Lightly press either side of the moon roof switch to stop the moon roof partway.

■ Tilting up and down

Opening and closing the windows

  1. Tilts the moon roof up*
  2. Tilts the moon roof down*

*: Lightly press either side of the moon roof switch to stop the moon roof partway.

■The moon roof can be operated when

The engine switch is in ON.

■Operating the moon roof after turning the engine off

The moon roof can be operated for approximately 45 seconds after the engine switch is turned to ACC or OFF. It cannot, however, be operated once either front door is opened.

■Jam protection function

If an object is detected between the moon roof and the frame while the moon roof is closing or tilting down, travel is stopped and the moon roof opens slightly.

■Sunshade

The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.

■Door lock linked moon roof operation

*: These settings must be customized at your Toyota dealer.

■When the moon roof does not close normally

Perform the following procedure:

1. Stop the vehicle.

2. Press and hold the "CLOSE" switch.*1

The moon roof will close, reopen and pause for approximately 10 seconds.* 2 Then it will close again, tilt up and pause for approximately 1 second. Finally, it will tilt down, open and close.

3. Check to make sure that the moon roof is completely closed and then release the switch.

1. Stop the vehicle.

2. Press and hold the "UP" switch*1 until the moon roof moves into the tilt up position and stops.

3. Release the "UP" switch once and then press and hold the "UP" switch again.*1

The moon roof will pause for approximately 10 seconds in the tilt up position.*2
Then it will adjust slightly and pause for approximately 1 second. Finally, it will tilt down, open and close.

4. Check to make sure that the moon roof is completely closed and then release the switch.

*1: If the switch is released at the incorrect time, the procedure will have to be performed again from the beginning.
*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the "CLOSE" or "UP" switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

If the moon roof does not fully close even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.

■Customization

Some functions can be customized.

WARNING

Observe the following precautions.

Failure to do so may cause death or serious injury.

■Opening the moon roof

■Opening and closing the moon roof

Opening and closing the windows

■Jam protection function

READ NEXT:

 Favorite settings

My Settings Drivers are identified using devices such as electronic keys to store the vehicle settings for each. Then the information can be recalled the next time the vehicle is driven. Authenticati

 Driving

 Before driving

SEE MORE:

 Active On-Demand Coupling Vehicles With: AWF21 6-Speed Automatic Transmission

Removal 1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle. 2. Refer to: Exhaust System (309-00B Exhaust System - TD4 2.2L Diesel, Removal and Installation). 3. CAUTION: Make sure that the driveshaft is supported with suitable retaining straps. 4. CAUTIONS:

 Drive Pinion Front Bearing

Special Tool(s) 100-012 Slide Hammer 205-067 Preload Gauge 308-615 Remover, Seals JLR-205-972 Mounting Bracket, Rear Axle JLR-205-984 Remover/Installer, Drive Pinion Nut JLR-205-985 Remover, Drive Pinion Bearing JLR-205-986 Installer, Drive Pinion Bearing Removal 1. Raise and support the vehicle. 2.

© 2011-2023 Copyright www.rrevoque.org